Higher accuracy with fewer projections? Automated scan angle selection for dimensional Computed Tomography based on a simple data completeness measure for the part surface
L. Butzhammer, M.R.O. Braun, C. Herath, T. Hausotte, in: E-Journal of Nondestructive Testing, NDT.net GmbH &; Co. KG, 2026.

Conversion between detector- and rotary-table-related misalignment parameterisations for unified projection-matrix-based geometry calibration in dimensional X-ray computed tomography
L. Butzhammer, Precision Engineering 100 (2026) 377–400.

Direct assessment of the influence of pose repeatability on the accuracy of dimensional measurements for computed tomography systems with high degrees of freedom
L. Butzhammer, N. Handke, S. Wittl, G. Herl, T. Hausotte, Measurement Science and Technology 36 (2025).

Non-destructive testing in versatile joining processes
M. Lechner, T. Borgert, M. Busch, A. Harms, P.K. Holtkamp, D. Römisch, S. Wituschek, F. Kappe, in: Materials Research Proceedings, Materials Research Forum LLC, 2025.

Task-specific scan trajectory modification for dimensional X-ray computed Tomography with high throughput
L. Butzhammer, T. Hausotte, Tm - Technisches Messen 91 (2024) 2–7.

Dynamic conformity assessment for joining force monitoring using Bayes filters
L. Butzhammer, F. Kappe, G. Meschut, T. Hausotte, in: Materials Research Proceedings, Materials Research Forum LLC, 2023.

Simulation-based investigation of the metrological interface structural resolution capability of X-ray computed tomography scanners
M. Busch, T. Hausotte, Journal of Sensors and Sensor Systems 12 (2023) 1–8.

Über die Abgrenzung von Auflösungskonzepten in der industriellen Computertomografie
F. Binder, T. Hausotte, Tm - Technisches Messen 89 (2022) 20–24.

Herausforderungen bei computertomografischen Untersuchungen von Fügeverbindungen
M. Busch, L. Butzhammer, T. Hausotte, Tm - Technisches Messen 89 (2022) 83–88.

Application of an edge detection algorithm for surface determination in industrial X-ray computed tomography
M. Busch, T. Hausotte, Production Engineering (2022).

Atomic Force Microscope with an Adjustable Probe Direction and Integrated Sensing and Actuation
J. Schaude, T. Hausotte, Nanomanufacturing and Metrology 5 (2022) 139–148.

Approach to Determine the Characteristic Dimensions of Clinched Joints by Industrial X-ray Computed Tomography
M. Busch, D. Köhler, T. Hausotte, R. Kupfer, J. Troschitz, M. Gude, in: 2022.

Clinching of Aluminum Materials – Methods for the Continuous Characterization of Process, Microstructure and Properties
R. Kupfer, D. Köhler, D. Römisch, S. Wituschek, L. Ewenz, J. Kalich, D. Weiß, B. Sadeghian, M. Busch, J.T. Krüger, M. Neuser, O. Grydin, M. Böhnke, C.R. Bielak, J. Troschitz, Journal of Advanced Joining Processes 5 (2022).

Calibration of 3D scan trajectories for an industrial computed tomography setup with 6-DOF object manipulator system using a single sphere
L. Butzhammer, A.M. Müller, T. Hausotte, Measurement Science and Technology 34 (2022).

Approach to Determine the Characteristic Dimensions of Clinched Joints by Industrial X-ray Computed Tomography
M. Busch, D. Köhler, T. Hausotte, R. Kupfer, J. Troschitz, M. Gude, E-Journal of Nondestructive Testing 27 (2022).

Determination of the Interface Structural Resolution of an Industrial X-Ray Computed Tomograph Using a Spherical Specimen and a Gap Specimen Consisting of Gauge Blocks
M. Busch, T. Hausotte, Key Engineering Materials 883 (2021) 41–48.

Joining suitability of cast aluminium for self-piercing riveting
M. Neuser, F. Kappe, M. Busch, O. Grydin, M. Bobbert, M. Schaper, G. Meschut, T. Hausotte, IOP Conference Series: Materials Science and Engineering (2021).