M. CIESLAR et al., “HOMOGENIZATION OF TWIN-ROLL CAST Al-Li-BASED ALLOY STUDIED BY IN-SITU ELECTRON MICROSCOPY,”10.37904/metal.2022.4438__presented at the Metal 2022, Brno, 2022, doi:10.37904/metal.2022.4438 .

C. R. Bielak, M. Böhnke, M. Bobbert, and G. Meschut, “Experimental and Numerical Investigation on Manufacturing-Induced Pre-Strain on the Load-Bearing Capacity of Clinched Joints,”10.4028/p-5d009y__Key Engineering Materials, vol. 926, pp. 1516–1526, 2022, doi:10.4028/p-5d009y .

M. Neukötter, S. Jesinghausen, and H.-J. Schmid, “Model droplet formation in extensional filament stretching within a Filament Extension Atomizer,”10.1007/s00397-022-01339-y__Rheologica Acta, 2022, doi:10.1007/s00397-022-01339-y .

S. Shaqiri, D. Kaczmarek, F. vom Lehn, J. Beeckmann, H. Pitsch, and T. Kasper, “Experimental Investigation of the Pressure Dependence of Iso-Octane Combustion,”10.3389/fenrg.2022.859112__Frontiers in Energy Research, vol. 10, 2022, doi:10.3389/fenrg.2022.859112 .

M. Hoener and T. Kasper, “Nitrous acid in high-pressure oxidation of C doped with nitric oxide: Challenges in the isomer-selective detection and quantification of an elusive intermediate,”10.1016/j.combustflame.2022.112096__Combustion and Flame, vol. 243, Art. no. 112096, 2022, doi:10.1016/j.combustflame.2022.112096 .

D. A. Knyazkov, A. V. Cherepanov, V. G. Kiselev, I. E. Gerasimov, T. Kasper, and A. G. Shmakov, “Experimental and kinetic modeling study of the positive ions in premixed ethylene flames over a range of equivalence ratios,”10.1016/j.proci.2022.07.157__Proceedings of the Combustion Institute, 2022, doi:10.1016/j.proci.2022.07.157 .

F. Beule, D. Teutenberg, and G. Meschut, “Directional dependence of the mechanical properties of structural adhesive joints with curing-induced pre-deformations,”10.1177/09544070221100130__Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering, Art. no. 095440702211001, 2022, doi:10.1177/09544070221100130 .

D. Kaczmarek et al., “Activation effect of ozone and DME on the partial oxidation of natural gas surrogates and validation of pressure-dependent ozone decomposition,”10.1016/j.jaecs.2022.100107__Applications in Energy and Combustion Science, Art. no. 100107, 2022, doi:10.1016/j.jaecs.2022.100107 .

D. Kaczmarek, C. Rudolph, B. Atakan, and T. Kasper, “Kinetic investigation of the ozone-assisted partial oxidation of fuel-rich natural gas mixtures at elevated pressure,”10.1016/j.proci.2022.07.195__Proceedings of the Combustion Institute, 2022, doi:10.1016/j.proci.2022.07.195 .

T. Bierkandt et al., “A combustion chemistry study of tetramethylethylene in a laminar premixed low-pressure hydrogen flame,”10.1016/j.proci.2022.07.205__Proceedings of the Combustion Institute, 2022, doi:10.1016/j.proci.2022.07.205 .

M. Böhnke, E. Unruh, S. Sell, M. Bobbert, D. Hein, and G. Meschut, “Functionality Study of an Optical Measurement Concept for Local Force Signal Determination in High Strain Rate Tensile Tests,”10.4028/p-wpuzyw__Key Engineering Materials, vol. 926, pp. 1564–1572, 2022, doi:10.4028/p-wpuzyw .

M. Böhnke, C. R. Bielak, M. Bobbert, and G. Meschut, “Development of a Modified Punch Test for Investigating the Failure Behavior in Sheet Metal Materials,” in The Minerals, Metals &;amp; Materials Series, Cham: Springer International Publishing, 2022.

M. Böhnke, C. R. Bielak, M. Bobbert, and G. Meschut, “Experimental and numerical investigation of the influence of multiaxial loading conditions on the failure behavior of clinched joints,”10.1177/14644207221145886__Proceedings of the Institution of Mechanical Engineers, Part L: Journal of Materials: Design and Applications, 2022, doi:10.1177/14644207221145886 .

H. Hanses and I. Horwath, “Development of operational and demand-oriented firefighting equipment,”10.1016/j.matpr.2022.06.031__Materials Today: Proceedings, vol. 62, no. 5, pp. 2684–2688, 2022, doi:10.1016/j.matpr.2022.06.031 .

L. Schmelzle et al., “Testing, modelling, and parameter identification for adhesively bonded joints under the influence of temperature,”10.1080/01694243.2022.2125714__Journal of Adhesion Science and Technology, 2022, doi:10.1080/01694243.2022.2125714 .

S. Neumann, G. Meschut, F. Schmatz, and W. Flügge, “Robotergestütztes manuelles mechanisches Fügen – RoboterFügen.”

M. Ott, N. Meihöfener, and R. Koch, “Neuronale Netze in der Konstruktion zur Ausschöpfung der Potentiale additiver Fertigungstechnologien,”10.48447/ADD-2022-014__in Bericht 407 - 7. Tagung des DVM-Arbeitskreises Additiv gefertigte Bauteile und Strukturen, Berlin, 2022, vol. 7, pp. 91–106, doi:10.48447/ADD-2022-014 .

S. Haller, S. R. Tinkloh, T. Tröster, and R. Brandt, “The environmental impact on the strain rate dependent energy absorption capability of a hybrid crash absorber element,” presented at the 5th International Conference Hybrid 2022 Material &; Structures, 2022.

F. Pfeifer, T. Tröster, T. Marten, A. Dietrich, B. Nacke, and G. Grundmeier, “Investigation on hot sheet metal forming by means of a longitudinal flux inductor,” presented at the 6th International Conference on Steels in Cars and Trucks, Mailand, 2022.

M. Dörner, Wave-Schnecken in der Einschneckenextrusion. 2022.