@article{33497,
  author       = {{Krüger, Jan Tobias}},
  journal      = {{crystals}},
  title        = {{{Adjustment of AgCaLa Phases in a FeMn Matrix via LBM for Implants with Adapted Degradation}}},
  doi          = {{https://doi.org/10.3390/cryst12081146}},
  volume       = {{12}},
  year         = {{2022}},
}

@inproceedings{36335,
  abstract     = {{Transformation of Fe- and Cu-rich primary phase particles was studied in an Al-Li-based alloy prepared by twin-roll casting. Thin foils for combined STEM and SEM experiments were prepared by electrolytic twin-jet polishing. They were in-situ heated in a TEM heating stage and observed at 200 kV in the JEOL JEM 2200FS electron microscope equipped with STEM HAADF and BF detectors and SEM BSE and SE detectors working both in composition and topographic modes. The resulting structures were combined with EDS mapping performed directly in the heating holder. Dissolution and transformation of Cu- and Fe-rich particles occur above 500 °C. EDS maps acquired on the foil cooled down to room temperature show that Cu and Fe are both still present in newly formed particles, most likely indicating the presence of the Al7Cu2Fe phase.}},
  author       = {{CIESLAR, Miroslav and KŘIVSKÁ, Barbora and KRÁLÍK, Rostislav and BAJTOŠOVÁ, Lucia and Grydin, Olexandr and STOLBCHENKO, Mykhailo and Schaper, Mirko}},
  booktitle    = {{METAL 2022 Conference Proeedings}},
  issn         = {{2694-9296}},
  keywords     = {{Al-Li-based alloy, in-situ TEM, homogenization, phase transformation}},
  location     = {{Brno}},
  publisher    = {{TANGER Ltd.}},
  title        = {{{HOMOGENIZATION OF TWIN-ROLL CAST Al-Li-BASED ALLOY STUDIED BY IN-SITU ELECTRON MICROSCOPY}}},
  doi          = {{10.37904/metal.2022.4438}},
  year         = {{2022}},
}

@article{36332,
  abstract     = {{AlSi casting alloys combine excellent castability with high strength. Hence, this group of alloys is often used in the automotive sector. The challenge for this application is the brittle character of these alloys which leads to cracks during joint formation when mechanical joining technologies are used. A rise in ductility can be achieved by a considerable increase in the solidification rate which results in grain refinement. High solidification rates can be realized in twin–roll casting (TRC) by water-cooled rolls. Therefore, a hypoeutectic EN AC–AlSi9 (for European Norm - aluminum cast product) is manufactured by the TRC process and analyzed. Subsequently, joining investigations are performed on castings in as-cast and heat-treated condition using the self-piercing riveting process considering the joint formation and the load-bearing capacity. Due to the fine microstructure, the crack initiation can be avoided during joining, while maintaining the joining parameters, especially by specimens in heat treatment conditions. Furthermore, due to the extremely fine microstructure, the load-bearing capacity of the joint can be significantly increased in terms of the maximum load-bearing force and the energy absorbed.}},
  author       = {{Neuser, Moritz and Kappe, Fabian and Ostermeier, Jakob and Krüger, Jan Tobias and Bobbert, Mathias and Meschut, Gerson and Schaper, Mirko and Grydin, Olexandr}},
  issn         = {{1438-1656}},
  journal      = {{Advanced Engineering Materials}},
  keywords     = {{Condensed Matter Physics, General Materials Science}},
  number       = {{10}},
  publisher    = {{Wiley}},
  title        = {{{Mechanical Properties and Joinability of AlSi9 Alloy Manufactured by Twin‐Roll Casting}}},
  doi          = {{10.1002/adem.202200874}},
  volume       = {{24}},
  year         = {{2022}},
}

@article{29724,
  abstract     = {{<jats:p> In many manufacturing areas, multi-material designs are implemented in which individual components are joined together to form complex structures with numerous joints. For example, in the automotive sector, cast components are used at the junctions of the body and joined with different types of sheet metal and extruded profiles. To be able to join structures consisting of different materials, alternative joining technologies have emerged in recent years. This includes clinching, which allows assembling of two or more thin sheet metal and casting parts by solely cold forming the material. Clinching the brittle and usually less ductile cast aluminium alloys remains a challenge because the brittle character of the cast aluminium alloys can cause cracks during the forming of the clinched joint. In this study, the influence of the heat treatment time of an aluminium casting alloy AlSi9 on the joinability in the clinching process is investigated. Specific heat treatment of the naturally hard AlSi9 leads to a modification of the eutectic microstructure, which can increase ductility. Based on this, it will be examined if specific clinching die geometries can be used, which achieve an optimized geometrical formation of the clinched joint. The load-bearing capacities of the clinched joints are determined and compared by shear tensile and head tensile tests. Furthermore, the joints are examined microscopically to investigate the influence of the heat treatment on the failure behaviour during the load-bearing tests as well as crack initiation within the joining process. </jats:p>}},
  author       = {{Neuser, Moritz and Böhnke, Max and Grydin, Olexandr and Bobbert, Mathias and Schaper, Mirko and Meschut, Gerson}},
  issn         = {{1464-4207}},
  journal      = {{Proceedings of the Institution of Mechanical Engineers, Part L: Journal of Materials: Design and Applications}},
  keywords     = {{Mechanical Engineering, General Materials Science}},
  publisher    = {{SAGE Publications}},
  title        = {{{Influence of heat treatment on the suitability for clinching of the aluminium casting alloy AlSi9}}},
  doi          = {{10.1177/14644207221075838}},
  year         = {{2022}},
}

@article{29505,
  abstract     = {{In modern vehicle chassis, multi-material design is implemented to apply the appropriate material for each functionality. In spaceframe technology, both sheet metal and continuous cast are joined to castings at the nodal points of the chassis. Since resistance spot welding is not an option when different materials are joined, research is focusing on mechanical joining methods for multi-material designs. To reduce weight and achieve the required strength, hardenable cast aluminium alloys of the AlSi-system are widely used. Thus, 85–90% of aluminium castings in the automotive industry are comprised of the AlSi-system. Due to the limited weldability, mechanical joining is a suitable process. For this application, various optimisation strategies are required to produce a crack-free joint, as the brittle character of the AlSi alloy poses a challenge. Thus, adapted castings with appropriate ductility are needed. Hence, in this study, the age-hardenable cast aluminium alloy AlSi10Mg is investigated regarding the correlation of the different thicknesses, the microstructural characteristics as well as the resulting mechanical properties. A variation of the thicknesses leads to different solidification rates, which in turn affect the microstructure formation and are decisive for the mechanical properties of the casting as well as the joinability. For the investigation, plates with thicknesses from 2.0 to 4.0 mm, each differing by 0.5 mm, are produced via sand casting. Hence, the overall aim is to evaluate the joinability of AlSi10Mg and derive conclusions concerning the microstructure and mechanical properties.</jats:p>}},
  author       = {{Neuser, Moritz and Grydin, Olexandr and Frolov, Y. and Schaper, Mirko}},
  issn         = {{0944-6524}},
  journal      = {{Production Engineering}},
  keywords     = {{Industrial and Manufacturing Engineering, Mechanical Engineering}},
  publisher    = {{Springer Science and Business Media LLC}},
  title        = {{{Influence of solidification rates and heat treatment on the mechanical performance and joinability of the cast aluminium alloy AlSi10Mg}}},
  doi          = {{10.1007/s11740-022-01106-1}},
  year         = {{2022}},
}

@article{31828,
  author       = {{Kupfer, Robert and Köhler, Daniel and Römisch, David and Wituschek, Simon and Ewenz, Lars and Kalich, Jan and Weiß, Deborah and Sadeghian, Behdad and Busch, Matthias and Krüger, Jan and Neuser, Moritz and Grydin, Olexandr and Böhnke, Max and Bielak, Christian Roman and Troschitz, Juliane}},
  issn         = {{2666-3309}},
  journal      = {{Journal of Advanced Joining Processes}},
  keywords     = {{Mechanical Engineering, Mechanics of Materials, Engineering (miscellaneous), Chemical Engineering (miscellaneous)}},
  publisher    = {{Elsevier BV}},
  title        = {{{Clinching of Aluminum Materials – Methods for the Continuous Characterization of Process, Microstructure and Properties}}},
  doi          = {{10.1016/j.jajp.2022.100108}},
  volume       = {{5}},
  year         = {{2022}},
}

@article{31238,
  author       = {{Kupfer, Robert and Köhler, Daniel and Römisch, David and Wituschek, Simon and Ewenz, Lars and Kalich, Jan and Weiß, Deborah and Sadeghian, Behdad and Busch, Matthias and Krüger, Jan Tobias and Neuser, Moritz and Grydin, Olexandr and Böhnke, Max and Bielak, Christian-Roman and Troschitz, Juliane}},
  issn         = {{2666-3309}},
  journal      = {{Journal of Advanced Joining Processes}},
  keywords     = {{Mechanical Engineering, Mechanics of Materials, Engineering (miscellaneous), Chemical Engineering (miscellaneous)}},
  publisher    = {{Elsevier BV}},
  title        = {{{Clinching of Aluminum Materials – Methods for the Continuous Characterization of Process, Microstructure and Properties}}},
  doi          = {{10.1016/j.jajp.2022.100108}},
  year         = {{2022}},
}

@inbook{29771,
  author       = {{Grydin, Olexandr and Mortensen, Dag and Neuser, Moritz and Lindholm, Dag and Fjaer, Hallvard G. and Schaper, Mirko}},
  booktitle    = {{Light Metals 2022}},
  isbn         = {{9783030925284}},
  issn         = {{2367-1181}},
  publisher    = {{Springer International Publishing}},
  title        = {{{Numerical and Experimental Investigation of Heat Transfer in the Solidification-Deformation Zone During Twin-Roll Casting of Aluminum Strips}}},
  doi          = {{10.1007/978-3-030-92529-1_96}},
  year         = {{2022}},
}

@article{34215,
  abstract     = {{Clinching as a mechanical joining technique allows a fast and reliable joining of metal sheets in large-scale production. An efficient design and dimensioning of clinched joints requires a holistic understanding of the material, the joining process and the resulting properties of the joint. In this paper, the process chain for clinching metal sheets is described and experimental techniques are proposed to analyze the process-microstructure-property relationships from the sheet metal to the joined structure. At the example of clinching aluminum EN AW 6014, characterization methods are applied and discussed for the following characteristics: the mechanical properties of the sheet materials, the tribological behavior in the joining system, the joining process and the resulting material structure, the load-bearing behavior of the joint, the damage and degradation as well as the service life and crack growth behavior. The compilation of the characterization methods gives an overview on the advantages and weaknesses of the methods and the multiple interactions of material, process and properties during clinching. In addition, the results of the analyses on EN AW 6014 can be applied for parameterization and validation of simulations.}},
  author       = {{Kupfer, Robert and Köhler, Daniel and Römisch, David and Wituschek, Simon and Ewenz, Lars and Kalich, Jan and Weiß, Deborah and Sadeghian, Behdad and Busch, Matthias and Krüger, Jan Tobias and Neuser, Moritz and Grydin, Olexandr and Böhnke, Max and Bielak, Christian Roman and Troschitz, Juliane}},
  issn         = {{2666-3309}},
  journal      = {{Journal of Advanced Joining Processes}},
  keywords     = {{Mechanical Engineering, Mechanics of Materials, Engineering (miscellaneous), Chemical Engineering (miscellaneous)}},
  publisher    = {{Elsevier BV}},
  title        = {{{Clinching of Aluminum Materials – Methods for the Continuous Characterization of Process, Microstructure and Properties}}},
  doi          = {{10.1016/j.jajp.2022.100108}},
  volume       = {{5}},
  year         = {{2022}},
}

@inproceedings{36339,
  abstract     = {{Al-Li-based alloys are an attractive material for aircraft and aerospace applications. Preparation of these alloys by twin-roll casting (TRC), which combines rapid metal solidification and subsequent plastic reduction in a single processing step, could improve the properties of the alloys compared to materials prepared by conventional direct-chill casting. A commonly used approach for identifying primary phases is a chemical analysis by energy dispersive spectroscopy (EDS). More accurate results can be achieved by combining the method with diffraction analysis. This process can be considerably simplified in microscopes equipped with automated crystal orientation and phase mapping (ACOM-TEM). Al-Cu-Li-Mg-Zr alloy was prepared by twin-roll casting. A combination of TEM and STEM images with chemical analysis by EDS and ACOM-TEM was used to obtain complex information about phases of boundary primary particles. The efficiency of the individual methods for the phase identification in TRC Al-Li-based alloys is discussed.}},
  author       = {{BAJTOŠOVÁ, Lucia and Grydin, Olexandr and STOLBCHENKO, Mykhailo and Schaper, Mirko and KŘIVSKÁ, Barbora and KRÁLÍK, Rostislav and ŠLAPÁKOVÁ, Michaela and CIESLAR, Miroslav}},
  booktitle    = {{METAL 2022 Conference Proeedings}},
  issn         = {{2694-9296}},
  keywords     = {{Al-Cu-Li-M-Zr-Fe alloy, twin-roll casting, phase identification, ACOM-TEM}},
  location     = {{Brno}},
  publisher    = {{TANGER Ltd.}},
  title        = {{{Phase identification in twin-roll cast Al-Li alloys}}},
  doi          = {{10.37904/metal.2022.4437}},
  year         = {{2022}},
}

@article{32188,
  abstract     = {{<jats:p>The additive manufacturing (AM) of innovative lattice structures with unique mechanical properties has received widespread attention due to the capability of AM processes to fabricate freeform and intricate structures. The most common way to characterize the additively manufactured lattice structures is via the uniaxial compression test. However, although there are many applications for which lattice structures are designed for bending (e.g., sandwich panels cores and some medical implants), limited attention has been paid toward investigating the flexural behavior of metallic AM lattice structures with tunable internal architectures. The purpose of this study was to experimentally investigate the flexural behavior of AM Ti-6Al-4V lattice structures with graded density and hybrid Poisson’s ratio (PR). Four configurations of lattice structure beams with positive, negative, hybrid PR, and a novel hybrid PR with graded density were manufactured via the laser powder bed fusion (LPBF) AM process and tested under four-point bending. The manufacturability, microstructure, micro-hardness, and flexural properties of the lattices were evaluated. During the bending tests, different failure mechanisms were observed, which were highly dependent on the type of lattice geometry. The best response in terms of absorbed energy was obtained for the functionally graded hybrid PR (FGHPR) structure. Both the FGHPR and hybrid PR (HPR) structured showed a 78.7% and 62.9% increase in the absorbed energy, respectively, compared to the positive PR (PPR) structure. This highlights the great potential for FGHPR lattices to be used in protective devices, load-bearing medical implants, and energy-absorbing applications.</jats:p>}},
  author       = {{Abdelaal, Osama and Hengsbach, Florian and Schaper, Mirko and Hoyer, Kay-Peter}},
  issn         = {{1996-1944}},
  journal      = {{Materials}},
  keywords     = {{General Materials Science}},
  number       = {{12}},
  publisher    = {{MDPI AG}},
  title        = {{{LPBF Manufactured Functionally Graded Lattice Structures Obtained by Graded Density and Hybrid Poisson’s Ratio}}},
  doi          = {{10.3390/ma15124072}},
  volume       = {{15}},
  year         = {{2022}},
}

@article{34097,
  author       = {{Voswinkel, Dietrich and Striewe, Jan Andre and Grydin, Olexandr and Meinderink, Dennis and Grundmeier, Guido and Schaper, Mirko and Tröster, Thomas}},
  issn         = {{0924-3046}},
  journal      = {{Advanced Composite Materials}},
  keywords     = {{Mechanical Engineering, Mechanics of Materials, Ceramics and Composites}},
  pages        = {{1--16}},
  publisher    = {{Informa UK Limited}},
  title        = {{{Co-bonding of carbon fibre-reinforced epoxy and galvanised steel with laser structured interface for automotive applications}}},
  doi          = {{10.1080/09243046.2022.2143746}},
  year         = {{2022}},
}

@article{30519,
  author       = {{Pramanik, Sudipta and Tasche, Frederik and Hoyer, Kay-Peter and Schaper, Mirko}},
  journal      = {{Magnetism}},
  pages        = {{88--104}},
  publisher    = {{MDPI}},
  title        = {{{Orientation-Dependent Indentation Behaviour of Additively Manufactured FeCo Sample: A Quasi In-Situ Study}}},
  doi          = {{10.3390/magnetism2020007}},
  volume       = {{2}},
  year         = {{2022}},
}

@article{36327,
  abstract     = {{<jats:title>Abstract</jats:title><jats:p>With an innovative optical characterization method, using high-temperature digital image correlation in combination with thermal imaging, the local change in strain and change in temperature could be determined during thermo-mechanical treatment of flat steel specimens. With data obtained by this optical method, the transformation kinetics for every area of interest along the whole measuring length of a flat specimen could be analyzed by the generation of dilatation curves. The benefit of this innovative optical characterization method compared to a dilatometer test is that the experimental effort for the design of a tailored component could be strongly reduced to the investigation of only a few tailored thermo-mechanical processed specimens. Due to the implementation of a strain and/or temperature gradient within the flat specimen, less metallographic samples are prepared for hardness analysis and analysis of the microstructural composition by scanning electron microscopy to investigate the influence of different process parameters. Compared to performed dilatometer tests in this study, the optical method obtained comparable results for the transformation start and end temperatures. For the final design of a part with tailored properties, the optical method is suitable for a time-efficient material characterization.</jats:p>
                <jats:p><jats:bold>Graphical Abstract</jats:bold></jats:p>}},
  author       = {{Reitz, Alexander and Grydin, Olexandr and Schaper, Mirko}},
  issn         = {{1073-5623}},
  journal      = {{Metallurgical and Materials Transactions A}},
  keywords     = {{Metals and Alloys, Mechanics of Materials, Condensed Matter Physics}},
  number       = {{8}},
  pages        = {{3125--3142}},
  publisher    = {{Springer Science and Business Media LLC}},
  title        = {{{Optical Detection of Phase Transformations in Steels: An Innovative Method for Time-Efficient Material Characterization During Tailored Thermo-mechanical Processing of a Press Hardening Steel}}},
  doi          = {{10.1007/s11661-022-06732-z}},
  volume       = {{53}},
  year         = {{2022}},
}

@article{40154,
  abstract     = {{<jats:p>The development of bioresorbable materials for temporary implantation enables progress in medical technology. Iron (Fe)-based degradable materials are biocompatible and exhibit good mechanical properties, but their degradation rate is low. Aside from alloying with Manganese (Mn), the creation of phases with high electrochemical potential such as silver (Ag) phases to cause the anodic dissolution of FeMn is promising. However, to enable residue-free dissolution, the Ag needs to be modified. This concern is addressed, as FeMn modified with a degradable Ag-Calcium-Lanthanum (AgCaLa) alloy is investigated. The electrochemical properties and the degradation behavior are determined via a static immersion test. The local differences in electrochemical potential increase the degradation rate (low pH values), and the formation of gaps around the Ag phases (neutral pH values) demonstrates the benefit of the strategy. Nevertheless, the formation of corrosion-inhibiting layers avoids an increased degradation rate under a neutral pH value. The complete bioresorption of the material is possible since the phases of the degradable AgCaLa alloy dissolve after the FeMn matrix. Cell viability tests reveal biocompatibility, and the antibacterial activity of the degradation supernatant is observed. Thus, FeMn modified with degradable AgCaLa phases is promising as a bioresorbable material if corrosion-inhibiting layers can be diminished.</jats:p>}},
  author       = {{Krüger, Jan Tobias and Hoyer, Kay-Peter and Huang, Jingyuan and Filor, Viviane and Mateus-Vargas, Rafael Hernan and Oltmanns, Hilke and Meißner, Jessica and Grundmeier, Guido and Schaper, Mirko}},
  issn         = {{2079-4983}},
  journal      = {{Journal of Functional Biomaterials}},
  keywords     = {{Biomedical Engineering, Biomaterials}},
  number       = {{4}},
  pages        = {{185}},
  publisher    = {{MDPI AG}},
  title        = {{{FeMn with Phases of a Degradable Ag Alloy for Residue-Free and Adapted Bioresorbability}}},
  doi          = {{10.3390/jfb13040185}},
  volume       = {{13}},
  year         = {{2022}},
}

@article{36328,
  abstract     = {{Aluminium-steel clad composite was manufactured by twin-roll casting. An intermetallic layer of Al5Fe2 and Al13Fe4 formed at the interface upon annealing above 500 °C. During in-situ annealing in transmission electron microscope, the layer grew towards the steel side of the interface in tongue-like protrusions. A study of furnace-annealed samples revealed, that the bulk growth of the interface phase proceeds towards the aluminium side. The growth towards steel is a surface effect that takes place simultaneously with the bulk growth towards aluminium. At the beginning of the intermetallic layer formation diffusion of Fe into aluminium prevails, afterwards Al atoms diffuse throught the newly formed intermetallic layer towards steel and the whole interface shifts towards aluminium. The kinetics of growth of the intermetallic layer follows parabolic law in both cases, indicating that the growth is governed by diffusion.}},
  author       = {{Šlapáková, Michaela and Křivská, Barbora and Fekete, Klaudia and Králík, Rostislav and Grydin, Olexandr and Stolbchenko, Mykhailo and Schaper, Mirko}},
  issn         = {{1044-5803}},
  journal      = {{Materials Characterization}},
  keywords     = {{Mechanical Engineering, Mechanics of Materials, Condensed Matter Physics, General Materials Science}},
  publisher    = {{Elsevier BV}},
  title        = {{{The influence of surface on direction of diffusion in Al-Fe clad material}}},
  doi          = {{10.1016/j.matchar.2022.112005}},
  volume       = {{190}},
  year         = {{2022}},
}

@article{23794,
  author       = {{Westermann, Hendrik and Reitz, Alexander and Mahnken, Rolf and Schaper, Mirko and Grydin, Olexandr}},
  issn         = {{1611-3683}},
  journal      = {{steel research international}},
  title        = {{{Microstructure transformations in a press hardening steel during tailored thermo‐mechanical processing}}},
  doi          = {{10.1002/srin.202100346}},
  year         = {{2022}},
}

@article{29196,
  abstract     = {{In biomedical engineering, laser powder bed fusion is an advanced manufacturing technology, which enables, for example, the production of patient-customized implants with complex geometries. Ti-6Al-7Nb shows promising improvements, especially regarding biocompatibility, compared with other titanium alloys. The biocompatible features are investigated employing cytocompatibility and antibacterial examinations on Al2O3-blasted and untreated surfaces. The mechanical properties of additively manufactured Ti-6Al-7Nb are evaluated in as-built and heat-treated conditions. Recrystallization annealing (925 °C for 4 h), β annealing (1050 °C for 2 h), as well as stress relieving (600 °C for 4 h) are applied. For microstructural investigation, scanning and transmission electron microscopy are performed. The different microstructures and the mechanical properties are compared. Mechanical behavior is determined based on quasi-static tensile tests and strain-controlled low cycle fatigue tests with total strain amplitudes εA of 0.35%, 0.5%, and 0.8%. The as-built and stress-relieved conditions meet the mechanical demands for the tensile properties of the international standard ISO 5832-11. Based on the Coffin–Manson–Basquin relation, fatigue strength and ductility coefficients, as well as exponents, are determined to examine fatigue life for the different conditions. The stress-relieved condition exhibits, overall, the best properties regarding monotonic tensile and cyclic fatigue behavior.</jats:p>}},
  author       = {{Hein, Maxwell and Kokalj, David and Lopes Dias, Nelson Filipe and Stangier, Dominic and Oltmanns, Hilke and Pramanik, Sudipta and Kietzmann, Manfred and Hoyer, Kay-Peter and Meißner, Jessica and Tillmann, Wolfgang and Schaper, Mirko}},
  issn         = {{2075-4701}},
  journal      = {{Metals}},
  keywords     = {{General Materials Science, Metals and Alloys, laser powder bed fusion, Ti-6Al-7Nb, titanium alloy, biomedical engineering, low cycle fatigue, microstructure, nanostructure}},
  number       = {{1}},
  publisher    = {{MDPI AG}},
  title        = {{{Low Cycle Fatigue Performance of Additively Processed and Heat-Treated Ti-6Al-7Nb Alloy for Biomedical Applications}}},
  doi          = {{10.3390/met12010122}},
  volume       = {{12}},
  year         = {{2022}},
}

@article{29811,
  abstract     = {{In order to reduce CO2 emissions in the transport sector, the approach of load-adapted components is increasingly being pursued. For the design of such components, it is crucial to determine their resulting microstructure and mechanical properties. For this purpose, continuous cooling transformation diagrams and deformation continuous cooling transformation diagrams are utilized, however, their curves are strongly influenced by the chemical composition, the initial state and especially the process parameters.

In this study, the influence of the process parameters on the transformation kinetics is systematically investigated using an innovative characterization method. The experimental setup allowed a near-process analysis of the transformation kinetics, resulting microstructure and mechanical properties for a specific process route with a reduced number of specimens. A systematic investigation of the effects of different process parameters on the microstructural and mechanical properties made it possible to reveal interactions and independencies between the process parameters in order to design a partial heating or differential cooling process. Furthermore, the implementation of two different cooling conditions, representative of differential cooling in the die relief method with tool-contact and non-contact areas, showed that the soaking duration has a significant influence on the microstructure in the non-contact tool area.}},
  author       = {{Reitz, Alexander and Grydin, Olexandr and Schaper, Mirko}},
  issn         = {{0921-5093}},
  journal      = {{Materials Science and Engineering: A}},
  keywords     = {{Mechanical Engineering, Mechanics of Materials, Condensed Matter Physics, General Materials Science}},
  publisher    = {{Elsevier BV}},
  title        = {{{Influence of thermomechanical processing on the microstructural and mechanical properties of steel 22MnB5}}},
  doi          = {{10.1016/j.msea.2022.142780}},
  volume       = {{838}},
  year         = {{2022}},
}

@article{33723,
  abstract     = {{<jats:p>The development of bioresorbable materials for temporary implantation enables progress in medical technology. Iron (Fe)-based degradable materials are biocompatible and exhibit good mechanical properties, but their degradation rate is low. Aside from alloying with Manganese (Mn), the creation of phases with high electrochemical potential such as silver (Ag) phases to cause the anodic dissolution of FeMn is promising. However, to enable residue-free dissolution, the Ag needs to be modified. This concern is addressed, as FeMn modified with a degradable Ag-Calcium-Lanthanum (AgCaLa) alloy is investigated. The electrochemical properties and the degradation behavior are determined via a static immersion test. The local differences in electrochemical potential increase the degradation rate (low pH values), and the formation of gaps around the Ag phases (neutral pH values) demonstrates the benefit of the strategy. Nevertheless, the formation of corrosion-inhibiting layers avoids an increased degradation rate under a neutral pH value. The complete bioresorption of the material is possible since the phases of the degradable AgCaLa alloy dissolve after the FeMn matrix. Cell viability tests reveal biocompatibility, and the antibacterial activity of the degradation supernatant is observed. Thus, FeMn modified with degradable AgCaLa phases is promising as a bioresorbable material if corrosion-inhibiting layers can be diminished.</jats:p>}},
  author       = {{Krüger, Jan Tobias and Hoyer, Kay-Peter and Huang, Jingyuan and Filor, Viviane and Mateus-Vargas, Rafael Hernan and Oltmanns, Hilke and Meißner, Jessica and Grundmeier, Guido and Schaper, Mirko}},
  issn         = {{2079-4983}},
  journal      = {{Journal of Functional Biomaterials}},
  keywords     = {{Biomedical Engineering, Biomaterials}},
  number       = {{4}},
  publisher    = {{MDPI AG}},
  title        = {{{FeMn with Phases of a Degradable Ag Alloy for Residue-Free and Adapted Bioresorbability}}},
  doi          = {{10.3390/jfb13040185}},
  volume       = {{13}},
  year         = {{2022}},
}