---
_id: '34214'
abstract:
- lang: eng
  text: This article presents the application and evaluation of a cantilever with
    integrated sensing and actuation as part of an atomic force microscope (AFM) with
    an adjustable probe direction, which is integrated into a nano measuring machine
    (NMM-1). The AFM, which is operated in closed-loop intermittent contact mode,
    is based on two rotational axes that enable the adjustment of the probe direction
    to cover a complete hemisphere. The axes greatly enlarge the metrology frame of
    the measuring system by materials with a comparatively high coefficient of thermal
    expansion, which ultimately limits the achievable measurement uncertainty of the
    measuring system. Thus, to reduce the thermal sensitivity of the system, the redesign
    of the rotational kinematics is mandatory. However, in this article, some preliminary
    investigations on the application of a self-sensing cantilever with an integrated
    micro heater for its stimulation will be presented. In previous investigations,
    a piezoelectric actuator has been applied to stimulate the cantilever. However,
    the removal of the piezoelectric actuator, which is enabled by the application
    of a cantilever with an integrated micro heater, promises an essential simplification
    of the sensor holder. Thus, in the future it might be possible to use materials
    with a low coefficient of thermal expansion, which are often difficult to machine
    and therefore only allow for rather simple geometries. Furthermore, because of
    the creepage of piezoelectric actuators, their removal from the metrology frame
    might lead to improved metrological characteristics. As will be shown, there are
    no significant differences between the two modes of actuation. Therefore, the
    redesigned rotational system will be based on the cantilever with integrated sensing
    and actuation.
author:
- first_name: Janik
  full_name: Schaude, Janik
  last_name: Schaude
- first_name: Tino
  full_name: Hausotte, Tino
  last_name: Hausotte
citation:
  ama: Schaude J, Hausotte T. Atomic Force Microscope with an Adjustable Probe Direction
    and Integrated Sensing and Actuation. <i>Nanomanufacturing and Metrology</i>.
    2022;5(2):139-148. doi:<a href="https://doi.org/10.1007/s41871-022-00143-9">10.1007/s41871-022-00143-9</a>
  apa: Schaude, J., &#38; Hausotte, T. (2022). Atomic Force Microscope with an Adjustable
    Probe Direction and Integrated Sensing and Actuation. <i>Nanomanufacturing and
    Metrology</i>, <i>5</i>(2), 139–148. <a href="https://doi.org/10.1007/s41871-022-00143-9">https://doi.org/10.1007/s41871-022-00143-9</a>
  bibtex: '@article{Schaude_Hausotte_2022, title={Atomic Force Microscope with an
    Adjustable Probe Direction and Integrated Sensing and Actuation}, volume={5},
    DOI={<a href="https://doi.org/10.1007/s41871-022-00143-9">10.1007/s41871-022-00143-9</a>},
    number={2}, journal={Nanomanufacturing and Metrology}, publisher={Springer Science
    and Business Media LLC}, author={Schaude, Janik and Hausotte, Tino}, year={2022},
    pages={139–148} }'
  chicago: 'Schaude, Janik, and Tino Hausotte. “Atomic Force Microscope with an Adjustable
    Probe Direction and Integrated Sensing and Actuation.” <i>Nanomanufacturing and
    Metrology</i> 5, no. 2 (2022): 139–48. <a href="https://doi.org/10.1007/s41871-022-00143-9">https://doi.org/10.1007/s41871-022-00143-9</a>.'
  ieee: 'J. Schaude and T. Hausotte, “Atomic Force Microscope with an Adjustable Probe
    Direction and Integrated Sensing and Actuation,” <i>Nanomanufacturing and Metrology</i>,
    vol. 5, no. 2, pp. 139–148, 2022, doi: <a href="https://doi.org/10.1007/s41871-022-00143-9">10.1007/s41871-022-00143-9</a>.'
  mla: Schaude, Janik, and Tino Hausotte. “Atomic Force Microscope with an Adjustable
    Probe Direction and Integrated Sensing and Actuation.” <i>Nanomanufacturing and
    Metrology</i>, vol. 5, no. 2, Springer Science and Business Media LLC, 2022, pp.
    139–48, doi:<a href="https://doi.org/10.1007/s41871-022-00143-9">10.1007/s41871-022-00143-9</a>.
  short: J. Schaude, T. Hausotte, Nanomanufacturing and Metrology 5 (2022) 139–148.
date_created: 2022-12-05T21:15:09Z
date_updated: 2023-01-02T11:10:08Z
department:
- _id: '630'
doi: 10.1007/s41871-022-00143-9
intvolume: '         5'
issue: '2'
keyword:
- Industrial and Manufacturing Engineering
- Mechanical Engineering
- Materials Science (miscellaneous)
language:
- iso: eng
page: 139-148
project:
- _id: '130'
  grant_number: '418701707'
  name: 'TRR 285: TRR 285'
- _id: '133'
  name: 'TRR 285 - C: TRR 285 - Project Area C'
- _id: '149'
  name: 'TRR 285 – C05: TRR 285 - Subproject C05'
publication: Nanomanufacturing and Metrology
publication_identifier:
  issn:
  - 2520-811X
  - 2520-8128
publication_status: published
publisher: Springer Science and Business Media LLC
status: public
title: Atomic Force Microscope with an Adjustable Probe Direction and Integrated Sensing
  and Actuation
type: journal_article
user_id: '14931'
volume: 5
year: '2022'
...
---
_id: '34414'
abstract:
- lang: eng
  text: Given a steadily increasing demand on multi-material lightweight designs,
    fast and cost-efficient production technologies, such as the mechanical joining
    process clinching, are becoming more and more relevant for series production.
    Since the application of such joining techniques often base on the ability to
    reach similar or even better joint loading capacities compared to established
    joining processes (e.g., spot welding), few contributions investigated the systematic
    improvement of clinch joint characteristics. In this regard, the use of data-driven
    methods in combination with optimization algorithms showed already high potentials
    for the analysis of individual joints and the definition of optimal tool configurations.
    However, the often missing consideration of uncertainties, such as varying material
    properties, and the related calculation of their impact on clinch joint properties
    can lead to poor estimation results and thus to a decreased reliability of the
    entire joint connection. This can cause major challenges, especially for the design
    and dimensioning of safety-relevant components, such as in car bodies. Motivated
    by this, the presented contribution introduces a novel method for the robust estimation
    of clinch joint characteristics including uncertainties of varying and versatile
    process chains in mechanical joining. Therefore, the utilization of Gaussian process
    regression models is demonstrated and evaluated regarding the ability to achieve
    sufficient prediction qualities.
author:
- first_name: Christoph
  full_name: Zirngibl, Christoph
  last_name: Zirngibl
- first_name: Benjamin
  full_name: Schleich, Benjamin
  last_name: Schleich
- first_name: Sandro
  full_name: Wartzack, Sandro
  last_name: Wartzack
citation:
  ama: Zirngibl C, Schleich B, Wartzack S. Robust estimation of clinch joint characteristics
    based on data-driven methods. <i>The International Journal of Advanced Manufacturing
    Technology</i>. Published online 2022. doi:<a href="https://doi.org/10.1007/s00170-022-10441-7">10.1007/s00170-022-10441-7</a>
  apa: Zirngibl, C., Schleich, B., &#38; Wartzack, S. (2022). Robust estimation of
    clinch joint characteristics based on data-driven methods. <i>The International
    Journal of Advanced Manufacturing Technology</i>. <a href="https://doi.org/10.1007/s00170-022-10441-7">https://doi.org/10.1007/s00170-022-10441-7</a>
  bibtex: '@article{Zirngibl_Schleich_Wartzack_2022, title={Robust estimation of clinch
    joint characteristics based on data-driven methods}, DOI={<a href="https://doi.org/10.1007/s00170-022-10441-7">10.1007/s00170-022-10441-7</a>},
    journal={The International Journal of Advanced Manufacturing Technology}, publisher={Springer
    Science and Business Media LLC}, author={Zirngibl, Christoph and Schleich, Benjamin
    and Wartzack, Sandro}, year={2022} }'
  chicago: Zirngibl, Christoph, Benjamin Schleich, and Sandro Wartzack. “Robust Estimation
    of Clinch Joint Characteristics Based on Data-Driven Methods.” <i>The International
    Journal of Advanced Manufacturing Technology</i>, 2022. <a href="https://doi.org/10.1007/s00170-022-10441-7">https://doi.org/10.1007/s00170-022-10441-7</a>.
  ieee: 'C. Zirngibl, B. Schleich, and S. Wartzack, “Robust estimation of clinch joint
    characteristics based on data-driven methods,” <i>The International Journal of
    Advanced Manufacturing Technology</i>, 2022, doi: <a href="https://doi.org/10.1007/s00170-022-10441-7">10.1007/s00170-022-10441-7</a>.'
  mla: Zirngibl, Christoph, et al. “Robust Estimation of Clinch Joint Characteristics
    Based on Data-Driven Methods.” <i>The International Journal of Advanced Manufacturing
    Technology</i>, Springer Science and Business Media LLC, 2022, doi:<a href="https://doi.org/10.1007/s00170-022-10441-7">10.1007/s00170-022-10441-7</a>.
  short: C. Zirngibl, B. Schleich, S. Wartzack, The International Journal of Advanced
    Manufacturing Technology (2022).
date_created: 2022-12-14T12:24:29Z
date_updated: 2023-01-02T11:14:26Z
department:
- _id: '630'
doi: 10.1007/s00170-022-10441-7
keyword:
- Industrial and Manufacturing Engineering
- Computer Science Applications
- Mechanical Engineering
- Software
- Control and Systems Engineering
language:
- iso: eng
main_file_link:
- open_access: '1'
  url: https://link.springer.com/article/10.1007/s00170-022-10441-7
oa: '1'
project:
- _id: '130'
  grant_number: '418701707'
  name: 'TRR 285: TRR 285'
- _id: '132'
  name: 'TRR 285 - B: TRR 285 - Project Area B'
- _id: '144'
  name: 'TRR 285 – B05: TRR 285 - Subproject B05'
publication: The International Journal of Advanced Manufacturing Technology
publication_identifier:
  issn:
  - 0268-3768
  - 1433-3015
publication_status: published
publisher: Springer Science and Business Media LLC
status: public
title: Robust estimation of clinch joint characteristics based on data-driven methods
type: journal_article
user_id: '14931'
year: '2022'
...
---
_id: '47562'
article_number: '117632'
author:
- first_name: Felix
  full_name: Herrmann, Felix
  last_name: Herrmann
- first_name: Marcus
  full_name: Grünewald, Marcus
  last_name: Grünewald
- first_name: Tobias
  full_name: Meijer, Tobias
  last_name: Meijer
- first_name: Ulrich
  full_name: Gardemann, Ulrich
  last_name: Gardemann
- first_name: Lukas
  full_name: Feierabend, Lukas
  last_name: Feierabend
- first_name: Julia
  full_name: Riese, Julia
  id: '101499'
  last_name: Riese
  orcid: 0000-0002-3053-0534
citation:
  ama: Herrmann F, Grünewald M, Meijer T, Gardemann U, Feierabend L, Riese J. Operating
    window and flexibility of a lab-scale methanation plant. <i>Chemical Engineering
    Science</i>. 2022;254. doi:<a href="https://doi.org/10.1016/j.ces.2022.117632">10.1016/j.ces.2022.117632</a>
  apa: Herrmann, F., Grünewald, M., Meijer, T., Gardemann, U., Feierabend, L., &#38;
    Riese, J. (2022). Operating window and flexibility of a lab-scale methanation
    plant. <i>Chemical Engineering Science</i>, <i>254</i>, Article 117632. <a href="https://doi.org/10.1016/j.ces.2022.117632">https://doi.org/10.1016/j.ces.2022.117632</a>
  bibtex: '@article{Herrmann_Grünewald_Meijer_Gardemann_Feierabend_Riese_2022, title={Operating
    window and flexibility of a lab-scale methanation plant}, volume={254}, DOI={<a
    href="https://doi.org/10.1016/j.ces.2022.117632">10.1016/j.ces.2022.117632</a>},
    number={117632}, journal={Chemical Engineering Science}, publisher={Elsevier BV},
    author={Herrmann, Felix and Grünewald, Marcus and Meijer, Tobias and Gardemann,
    Ulrich and Feierabend, Lukas and Riese, Julia}, year={2022} }'
  chicago: Herrmann, Felix, Marcus Grünewald, Tobias Meijer, Ulrich Gardemann, Lukas
    Feierabend, and Julia Riese. “Operating Window and Flexibility of a Lab-Scale
    Methanation Plant.” <i>Chemical Engineering Science</i> 254 (2022). <a href="https://doi.org/10.1016/j.ces.2022.117632">https://doi.org/10.1016/j.ces.2022.117632</a>.
  ieee: 'F. Herrmann, M. Grünewald, T. Meijer, U. Gardemann, L. Feierabend, and J.
    Riese, “Operating window and flexibility of a lab-scale methanation plant,” <i>Chemical
    Engineering Science</i>, vol. 254, Art. no. 117632, 2022, doi: <a href="https://doi.org/10.1016/j.ces.2022.117632">10.1016/j.ces.2022.117632</a>.'
  mla: Herrmann, Felix, et al. “Operating Window and Flexibility of a Lab-Scale Methanation
    Plant.” <i>Chemical Engineering Science</i>, vol. 254, 117632, Elsevier BV, 2022,
    doi:<a href="https://doi.org/10.1016/j.ces.2022.117632">10.1016/j.ces.2022.117632</a>.
  short: F. Herrmann, M. Grünewald, T. Meijer, U. Gardemann, L. Feierabend, J. Riese,
    Chemical Engineering Science 254 (2022).
date_created: 2023-10-04T14:15:40Z
date_updated: 2024-03-08T11:39:03Z
doi: 10.1016/j.ces.2022.117632
extern: '1'
intvolume: '       254'
keyword:
- Applied Mathematics
- Industrial and Manufacturing Engineering
- General Chemical Engineering
- General Chemistry
language:
- iso: eng
publication: Chemical Engineering Science
publication_identifier:
  issn:
  - 0009-2509
publication_status: published
publisher: Elsevier BV
quality_controlled: '1'
status: public
title: Operating window and flexibility of a lab-scale methanation plant
type: journal_article
user_id: '101499'
volume: 254
year: '2022'
...
---
_id: '47561'
abstract:
- lang: eng
  text: <jats:title>Abstract</jats:title><jats:p>Additive manufacturing is a promising
    tool for tailored solutions in chemical engineering. This applies in particular
    to the design of lab‐scale packed bed columns. We present experimental results
    to characterize a lab‐scale 3D printed structured metal packing and compare it
    to a conventional counterpart. The results indicate that necessary adjustments
    for the manufacturing process of the metal material have an influence on important
    operating parameters, resulting in higher specific pressure drop, slightly higher
    liquid holdup and lower mass transfer efficiency.</jats:p>
author:
- first_name: Julia
  full_name: Riese, Julia
  id: '101499'
  last_name: Riese
  orcid: 0000-0002-3053-0534
- first_name: Arnulf
  full_name: Reitze, Arnulf
  last_name: Reitze
- first_name: Marcus
  full_name: Grünewald, Marcus
  last_name: Grünewald
citation:
  ama: Riese J, Reitze A, Grünewald M. Experimental Characterization of 3D Printed
    Structured Metal Packing with an Enclosed Column Wall. <i>Chemie Ingenieur Technik</i>.
    2022;94(7):993-1001. doi:<a href="https://doi.org/10.1002/cite.202200002">10.1002/cite.202200002</a>
  apa: Riese, J., Reitze, A., &#38; Grünewald, M. (2022). Experimental Characterization
    of 3D Printed Structured Metal Packing with an Enclosed Column Wall. <i>Chemie
    Ingenieur Technik</i>, <i>94</i>(7), 993–1001. <a href="https://doi.org/10.1002/cite.202200002">https://doi.org/10.1002/cite.202200002</a>
  bibtex: '@article{Riese_Reitze_Grünewald_2022, title={Experimental Characterization
    of 3D Printed Structured Metal Packing with an Enclosed Column Wall}, volume={94},
    DOI={<a href="https://doi.org/10.1002/cite.202200002">10.1002/cite.202200002</a>},
    number={7}, journal={Chemie Ingenieur Technik}, publisher={Wiley}, author={Riese,
    Julia and Reitze, Arnulf and Grünewald, Marcus}, year={2022}, pages={993–1001}
    }'
  chicago: 'Riese, Julia, Arnulf Reitze, and Marcus Grünewald. “Experimental Characterization
    of 3D Printed Structured Metal Packing with an Enclosed Column Wall.” <i>Chemie
    Ingenieur Technik</i> 94, no. 7 (2022): 993–1001. <a href="https://doi.org/10.1002/cite.202200002">https://doi.org/10.1002/cite.202200002</a>.'
  ieee: 'J. Riese, A. Reitze, and M. Grünewald, “Experimental Characterization of
    3D Printed Structured Metal Packing with an Enclosed Column Wall,” <i>Chemie Ingenieur
    Technik</i>, vol. 94, no. 7, pp. 993–1001, 2022, doi: <a href="https://doi.org/10.1002/cite.202200002">10.1002/cite.202200002</a>.'
  mla: Riese, Julia, et al. “Experimental Characterization of 3D Printed Structured
    Metal Packing with an Enclosed Column Wall.” <i>Chemie Ingenieur Technik</i>,
    vol. 94, no. 7, Wiley, 2022, pp. 993–1001, doi:<a href="https://doi.org/10.1002/cite.202200002">10.1002/cite.202200002</a>.
  short: J. Riese, A. Reitze, M. Grünewald, Chemie Ingenieur Technik 94 (2022) 993–1001.
date_created: 2023-10-04T14:15:30Z
date_updated: 2024-03-08T11:31:40Z
doi: 10.1002/cite.202200002
extern: '1'
intvolume: '        94'
issue: '7'
keyword:
- Industrial and Manufacturing Engineering
- General Chemical Engineering
- General Chemistry
language:
- iso: eng
page: 993-1001
publication: Chemie Ingenieur Technik
publication_identifier:
  issn:
  - 0009-286X
  - 1522-2640
publication_status: published
publisher: Wiley
quality_controlled: '1'
status: public
title: Experimental Characterization of 3D Printed Structured Metal Packing with an
  Enclosed Column Wall
type: journal_article
user_id: '101499'
volume: 94
year: '2022'
...
---
_id: '47556'
author:
- first_name: Felix
  full_name: Herrmann, Felix
  last_name: Herrmann
- first_name: Marcus
  full_name: Grünewald, Marcus
  last_name: Grünewald
- first_name: Tobias
  full_name: Meijer, Tobias
  last_name: Meijer
- first_name: Ulrich
  full_name: Gardemann, Ulrich
  last_name: Gardemann
- first_name: Julia
  full_name: Riese, Julia
  id: '101499'
  last_name: Riese
  orcid: 0000-0002-3053-0534
citation:
  ama: Herrmann F, Grünewald M, Meijer T, Gardemann U, Riese J. Performance of a Laboratory-Scale
    Methanation Plant with Catalyst Dilution under Dynamic Operating Conditions. <i>Industrial
    &#38;amp; Engineering Chemistry Research</i>. 2022;61(27):9644-9657. doi:<a href="https://doi.org/10.1021/acs.iecr.2c00871">10.1021/acs.iecr.2c00871</a>
  apa: Herrmann, F., Grünewald, M., Meijer, T., Gardemann, U., &#38; Riese, J. (2022).
    Performance of a Laboratory-Scale Methanation Plant with Catalyst Dilution under
    Dynamic Operating Conditions. <i>Industrial &#38;amp; Engineering Chemistry Research</i>,
    <i>61</i>(27), 9644–9657. <a href="https://doi.org/10.1021/acs.iecr.2c00871">https://doi.org/10.1021/acs.iecr.2c00871</a>
  bibtex: '@article{Herrmann_Grünewald_Meijer_Gardemann_Riese_2022, title={Performance
    of a Laboratory-Scale Methanation Plant with Catalyst Dilution under Dynamic Operating
    Conditions}, volume={61}, DOI={<a href="https://doi.org/10.1021/acs.iecr.2c00871">10.1021/acs.iecr.2c00871</a>},
    number={27}, journal={Industrial &#38;amp; Engineering Chemistry Research}, publisher={American
    Chemical Society (ACS)}, author={Herrmann, Felix and Grünewald, Marcus and Meijer,
    Tobias and Gardemann, Ulrich and Riese, Julia}, year={2022}, pages={9644–9657}
    }'
  chicago: 'Herrmann, Felix, Marcus Grünewald, Tobias Meijer, Ulrich Gardemann, and
    Julia Riese. “Performance of a Laboratory-Scale Methanation Plant with Catalyst
    Dilution under Dynamic Operating Conditions.” <i>Industrial &#38;amp; Engineering
    Chemistry Research</i> 61, no. 27 (2022): 9644–57. <a href="https://doi.org/10.1021/acs.iecr.2c00871">https://doi.org/10.1021/acs.iecr.2c00871</a>.'
  ieee: 'F. Herrmann, M. Grünewald, T. Meijer, U. Gardemann, and J. Riese, “Performance
    of a Laboratory-Scale Methanation Plant with Catalyst Dilution under Dynamic Operating
    Conditions,” <i>Industrial &#38;amp; Engineering Chemistry Research</i>, vol.
    61, no. 27, pp. 9644–9657, 2022, doi: <a href="https://doi.org/10.1021/acs.iecr.2c00871">10.1021/acs.iecr.2c00871</a>.'
  mla: Herrmann, Felix, et al. “Performance of a Laboratory-Scale Methanation Plant
    with Catalyst Dilution under Dynamic Operating Conditions.” <i>Industrial &#38;amp;
    Engineering Chemistry Research</i>, vol. 61, no. 27, American Chemical Society
    (ACS), 2022, pp. 9644–57, doi:<a href="https://doi.org/10.1021/acs.iecr.2c00871">10.1021/acs.iecr.2c00871</a>.
  short: F. Herrmann, M. Grünewald, T. Meijer, U. Gardemann, J. Riese, Industrial
    &#38;amp; Engineering Chemistry Research 61 (2022) 9644–9657.
date_created: 2023-10-04T14:13:23Z
date_updated: 2024-03-08T11:31:49Z
doi: 10.1021/acs.iecr.2c00871
extern: '1'
intvolume: '        61'
issue: '27'
keyword:
- Industrial and Manufacturing Engineering
- General Chemical Engineering
- General Chemistry
language:
- iso: eng
page: 9644-9657
publication: Industrial &amp; Engineering Chemistry Research
publication_identifier:
  issn:
  - 0888-5885
  - 1520-5045
publication_status: published
publisher: American Chemical Society (ACS)
quality_controlled: '1'
status: public
title: Performance of a Laboratory-Scale Methanation Plant with Catalyst Dilution
  under Dynamic Operating Conditions
type: journal_article
user_id: '101499'
volume: 61
year: '2022'
...
---
_id: '40644'
article_number: '119596'
article_type: original
author:
- first_name: Abbas Jarullah Sangoor
  full_name: Al-Lami, Abbas Jarullah Sangoor
  id: '81772'
  last_name: Al-Lami
- first_name: Eugeny Y.
  full_name: Kenig, Eugeny Y.
  id: '665'
  last_name: Kenig
- first_name: Venkatesh
  full_name: Inguva, Venkatesh
  id: '75069'
  last_name: Inguva
citation:
  ama: Al-Lami AJS, Kenig EY, Inguva V. Numerical analysis of conjugate heat transfer
    within internally channeled tubes. <i>Applied Thermal Engineering</i>. 2022;223.
    doi:<a href="https://doi.org/10.1016/j.applthermaleng.2022.119596">10.1016/j.applthermaleng.2022.119596</a>
  apa: Al-Lami, A. J. S., Kenig, E. Y., &#38; Inguva, V. (2022). Numerical analysis
    of conjugate heat transfer within internally channeled tubes. <i>Applied Thermal
    Engineering</i>, <i>223</i>, Article 119596. <a href="https://doi.org/10.1016/j.applthermaleng.2022.119596">https://doi.org/10.1016/j.applthermaleng.2022.119596</a>
  bibtex: '@article{Al-Lami_Kenig_Inguva_2022, title={Numerical analysis of conjugate
    heat transfer within internally channeled tubes}, volume={223}, DOI={<a href="https://doi.org/10.1016/j.applthermaleng.2022.119596">10.1016/j.applthermaleng.2022.119596</a>},
    number={119596}, journal={Applied Thermal Engineering}, publisher={Elsevier BV},
    author={Al-Lami, Abbas Jarullah Sangoor and Kenig, Eugeny Y. and Inguva, Venkatesh},
    year={2022} }'
  chicago: Al-Lami, Abbas Jarullah Sangoor, Eugeny Y. Kenig, and Venkatesh Inguva.
    “Numerical Analysis of Conjugate Heat Transfer within Internally Channeled Tubes.”
    <i>Applied Thermal Engineering</i> 223 (2022). <a href="https://doi.org/10.1016/j.applthermaleng.2022.119596">https://doi.org/10.1016/j.applthermaleng.2022.119596</a>.
  ieee: 'A. J. S. Al-Lami, E. Y. Kenig, and V. Inguva, “Numerical analysis of conjugate
    heat transfer within internally channeled tubes,” <i>Applied Thermal Engineering</i>,
    vol. 223, Art. no. 119596, 2022, doi: <a href="https://doi.org/10.1016/j.applthermaleng.2022.119596">10.1016/j.applthermaleng.2022.119596</a>.'
  mla: Al-Lami, Abbas Jarullah Sangoor, et al. “Numerical Analysis of Conjugate Heat
    Transfer within Internally Channeled Tubes.” <i>Applied Thermal Engineering</i>,
    vol. 223, 119596, Elsevier BV, 2022, doi:<a href="https://doi.org/10.1016/j.applthermaleng.2022.119596">10.1016/j.applthermaleng.2022.119596</a>.
  short: A.J.S. Al-Lami, E.Y. Kenig, V. Inguva, Applied Thermal Engineering 223 (2022).
date_created: 2023-01-30T10:04:47Z
date_updated: 2024-03-09T08:34:35Z
doi: 10.1016/j.applthermaleng.2022.119596
has_accepted_license: '1'
intvolume: '       223'
keyword:
- Industrial and Manufacturing Engineering
- Energy Engineering and Power Technology
language:
- iso: eng
publication: Applied Thermal Engineering
publication_identifier:
  issn:
  - 1359-4311
publication_status: published
publisher: Elsevier BV
quality_controlled: '1'
status: public
title: Numerical analysis of conjugate heat transfer within internally channeled tubes
type: journal_article
user_id: '81772'
volume: 223
year: '2022'
...
---
_id: '29505'
abstract:
- lang: eng
  text: In modern vehicle chassis, multi-material design is implemented to apply the
    appropriate material for each functionality. In spaceframe technology, both sheet
    metal and continuous cast are joined to castings at the nodal points of the chassis.
    Since resistance spot welding is not an option when different materials are joined,
    research is focusing on mechanical joining methods for multi-material designs.
    To reduce weight and achieve the required strength, hardenable cast aluminium
    alloys of the AlSi-system are widely used. Thus, 85–90% of aluminium castings
    in the automotive industry are comprised of the AlSi-system. Due to the limited
    weldability, mechanical joining is a suitable process. For this application, various
    optimisation strategies are required to produce a crack-free joint, as the brittle
    character of the AlSi alloy poses a challenge. Thus, adapted castings with appropriate
    ductility are needed. Hence, in this study, the age-hardenable cast aluminium
    alloy AlSi10Mg is investigated regarding the correlation of the different thicknesses,
    the microstructural characteristics as well as the resulting mechanical properties.
    A variation of the thicknesses leads to different solidification rates, which
    in turn affect the microstructure formation and are decisive for the mechanical
    properties of the casting as well as the joinability. For the investigation, plates
    with thicknesses from 2.0 to 4.0 mm, each differing by 0.5 mm, are produced via
    sand casting. Hence, the overall aim is to evaluate the joinability of AlSi10Mg
    and derive conclusions concerning the microstructure and mechanical properties.</jats:p>
article_type: original
author:
- first_name: Moritz
  full_name: Neuser, Moritz
  id: '32340'
  last_name: Neuser
- first_name: Olexandr
  full_name: Grydin, Olexandr
  id: '43822'
  last_name: Grydin
- first_name: Y.
  full_name: Frolov, Y.
  last_name: Frolov
- first_name: Mirko
  full_name: Schaper, Mirko
  id: '43720'
  last_name: Schaper
citation:
  ama: Neuser M, Grydin O, Frolov Y, Schaper M. Influence of solidification rates
    and heat treatment on the mechanical performance and joinability of the cast aluminium
    alloy AlSi10Mg. <i>Production Engineering</i>. Published online 2022. doi:<a href="https://doi.org/10.1007/s11740-022-01106-1">10.1007/s11740-022-01106-1</a>
  apa: Neuser, M., Grydin, O., Frolov, Y., &#38; Schaper, M. (2022). Influence of
    solidification rates and heat treatment on the mechanical performance and joinability
    of the cast aluminium alloy AlSi10Mg. <i>Production Engineering</i>. <a href="https://doi.org/10.1007/s11740-022-01106-1">https://doi.org/10.1007/s11740-022-01106-1</a>
  bibtex: '@article{Neuser_Grydin_Frolov_Schaper_2022, title={Influence of solidification
    rates and heat treatment on the mechanical performance and joinability of the
    cast aluminium alloy AlSi10Mg}, DOI={<a href="https://doi.org/10.1007/s11740-022-01106-1">10.1007/s11740-022-01106-1</a>},
    journal={Production Engineering}, publisher={Springer Science and Business Media
    LLC}, author={Neuser, Moritz and Grydin, Olexandr and Frolov, Y. and Schaper,
    Mirko}, year={2022} }'
  chicago: Neuser, Moritz, Olexandr Grydin, Y. Frolov, and Mirko Schaper. “Influence
    of Solidification Rates and Heat Treatment on the Mechanical Performance and Joinability
    of the Cast Aluminium Alloy AlSi10Mg.” <i>Production Engineering</i>, 2022. <a
    href="https://doi.org/10.1007/s11740-022-01106-1">https://doi.org/10.1007/s11740-022-01106-1</a>.
  ieee: 'M. Neuser, O. Grydin, Y. Frolov, and M. Schaper, “Influence of solidification
    rates and heat treatment on the mechanical performance and joinability of the
    cast aluminium alloy AlSi10Mg,” <i>Production Engineering</i>, 2022, doi: <a href="https://doi.org/10.1007/s11740-022-01106-1">10.1007/s11740-022-01106-1</a>.'
  mla: Neuser, Moritz, et al. “Influence of Solidification Rates and Heat Treatment
    on the Mechanical Performance and Joinability of the Cast Aluminium Alloy AlSi10Mg.”
    <i>Production Engineering</i>, Springer Science and Business Media LLC, 2022,
    doi:<a href="https://doi.org/10.1007/s11740-022-01106-1">10.1007/s11740-022-01106-1</a>.
  short: M. Neuser, O. Grydin, Y. Frolov, M. Schaper, Production Engineering (2022).
date_created: 2022-01-24T08:27:48Z
date_updated: 2024-03-14T15:21:51Z
department:
- _id: '43'
- _id: '158'
- _id: '321'
- _id: '630'
doi: 10.1007/s11740-022-01106-1
keyword:
- Industrial and Manufacturing Engineering
- Mechanical Engineering
language:
- iso: eng
project:
- _id: '130'
  grant_number: '418701707'
  name: 'TRR 285: TRR 285'
- _id: '131'
  name: 'TRR 285 - A: TRR 285 - Project Area A'
- _id: '136'
  name: 'TRR 285 – A02: TRR 285 - Subproject A02'
publication: Production Engineering
publication_identifier:
  issn:
  - 0944-6524
  - 1863-7353
publication_status: published
publisher: Springer Science and Business Media LLC
quality_controlled: '1'
status: public
title: Influence of solidification rates and heat treatment on the mechanical performance
  and joinability of the cast aluminium alloy AlSi10Mg
type: journal_article
user_id: '32340'
year: '2022'
...
---
_id: '53237'
article_number: '129777'
author:
- first_name: Madjid
  full_name: Tavana, Madjid
  id: '31858'
  last_name: Tavana
- first_name: Hadi
  full_name: Kian, Hadi
  last_name: Kian
- first_name: Arash Khalili
  full_name: Nasr, Arash Khalili
  last_name: Nasr
- first_name: Kannan
  full_name: Govindan, Kannan
  last_name: Govindan
- first_name: Hassan
  full_name: Mina, Hassan
  last_name: Mina
citation:
  ama: Tavana M, Kian H, Nasr AK, Govindan K, Mina H. A comprehensive framework for
    sustainable closed-loop supply chain network design. <i>Journal of Cleaner Production</i>.
    2022;332. doi:<a href="https://doi.org/10.1016/j.jclepro.2021.129777">10.1016/j.jclepro.2021.129777</a>
  apa: Tavana, M., Kian, H., Nasr, A. K., Govindan, K., &#38; Mina, H. (2022). A comprehensive
    framework for sustainable closed-loop supply chain network design. <i>Journal
    of Cleaner Production</i>, <i>332</i>, Article 129777. <a href="https://doi.org/10.1016/j.jclepro.2021.129777">https://doi.org/10.1016/j.jclepro.2021.129777</a>
  bibtex: '@article{Tavana_Kian_Nasr_Govindan_Mina_2022, title={A comprehensive framework
    for sustainable closed-loop supply chain network design}, volume={332}, DOI={<a
    href="https://doi.org/10.1016/j.jclepro.2021.129777">10.1016/j.jclepro.2021.129777</a>},
    number={129777}, journal={Journal of Cleaner Production}, publisher={Elsevier
    BV}, author={Tavana, Madjid and Kian, Hadi and Nasr, Arash Khalili and Govindan,
    Kannan and Mina, Hassan}, year={2022} }'
  chicago: Tavana, Madjid, Hadi Kian, Arash Khalili Nasr, Kannan Govindan, and Hassan
    Mina. “A Comprehensive Framework for Sustainable Closed-Loop Supply Chain Network
    Design.” <i>Journal of Cleaner Production</i> 332 (2022). <a href="https://doi.org/10.1016/j.jclepro.2021.129777">https://doi.org/10.1016/j.jclepro.2021.129777</a>.
  ieee: 'M. Tavana, H. Kian, A. K. Nasr, K. Govindan, and H. Mina, “A comprehensive
    framework for sustainable closed-loop supply chain network design,” <i>Journal
    of Cleaner Production</i>, vol. 332, Art. no. 129777, 2022, doi: <a href="https://doi.org/10.1016/j.jclepro.2021.129777">10.1016/j.jclepro.2021.129777</a>.'
  mla: Tavana, Madjid, et al. “A Comprehensive Framework for Sustainable Closed-Loop
    Supply Chain Network Design.” <i>Journal of Cleaner Production</i>, vol. 332,
    129777, Elsevier BV, 2022, doi:<a href="https://doi.org/10.1016/j.jclepro.2021.129777">10.1016/j.jclepro.2021.129777</a>.
  short: M. Tavana, H. Kian, A.K. Nasr, K. Govindan, H. Mina, Journal of Cleaner Production
    332 (2022).
date_created: 2024-04-04T15:49:44Z
date_updated: 2024-04-15T13:16:19Z
department:
- _id: '277'
doi: 10.1016/j.jclepro.2021.129777
intvolume: '       332'
keyword:
- Industrial and Manufacturing Engineering
- Strategy and Management
- General Environmental Science
- Renewable Energy
- Sustainability and the Environment
language:
- iso: eng
publication: Journal of Cleaner Production
publication_identifier:
  issn:
  - 0959-6526
publication_status: published
publisher: Elsevier BV
status: public
title: A comprehensive framework for sustainable closed-loop supply chain network
  design
type: journal_article
user_id: '51811'
volume: 332
year: '2022'
...
---
_id: '53242'
article_number: '130409'
author:
- first_name: Ali
  full_name: Ebadi Torkayesh, Ali
  last_name: Ebadi Torkayesh
- first_name: Madjid
  full_name: Tavana, Madjid
  id: '31858'
  last_name: Tavana
- first_name: Francisco J.
  full_name: Santos-Arteaga, Francisco J.
  last_name: Santos-Arteaga
citation:
  ama: Ebadi Torkayesh A, Tavana M, Santos-Arteaga FJ. A multi-distance interval-valued
    neutrosophic approach for social failure detection in sustainable municipal waste
    management. <i>Journal of Cleaner Production</i>. 2022;336. doi:<a href="https://doi.org/10.1016/j.jclepro.2022.130409">10.1016/j.jclepro.2022.130409</a>
  apa: Ebadi Torkayesh, A., Tavana, M., &#38; Santos-Arteaga, F. J. (2022). A multi-distance
    interval-valued neutrosophic approach for social failure detection in sustainable
    municipal waste management. <i>Journal of Cleaner Production</i>, <i>336</i>,
    Article 130409. <a href="https://doi.org/10.1016/j.jclepro.2022.130409">https://doi.org/10.1016/j.jclepro.2022.130409</a>
  bibtex: '@article{Ebadi Torkayesh_Tavana_Santos-Arteaga_2022, title={A multi-distance
    interval-valued neutrosophic approach for social failure detection in sustainable
    municipal waste management}, volume={336}, DOI={<a href="https://doi.org/10.1016/j.jclepro.2022.130409">10.1016/j.jclepro.2022.130409</a>},
    number={130409}, journal={Journal of Cleaner Production}, publisher={Elsevier
    BV}, author={Ebadi Torkayesh, Ali and Tavana, Madjid and Santos-Arteaga, Francisco
    J.}, year={2022} }'
  chicago: Ebadi Torkayesh, Ali, Madjid Tavana, and Francisco J. Santos-Arteaga. “A
    Multi-Distance Interval-Valued Neutrosophic Approach for Social Failure Detection
    in Sustainable Municipal Waste Management.” <i>Journal of Cleaner Production</i>
    336 (2022). <a href="https://doi.org/10.1016/j.jclepro.2022.130409">https://doi.org/10.1016/j.jclepro.2022.130409</a>.
  ieee: 'A. Ebadi Torkayesh, M. Tavana, and F. J. Santos-Arteaga, “A multi-distance
    interval-valued neutrosophic approach for social failure detection in sustainable
    municipal waste management,” <i>Journal of Cleaner Production</i>, vol. 336, Art.
    no. 130409, 2022, doi: <a href="https://doi.org/10.1016/j.jclepro.2022.130409">10.1016/j.jclepro.2022.130409</a>.'
  mla: Ebadi Torkayesh, Ali, et al. “A Multi-Distance Interval-Valued Neutrosophic
    Approach for Social Failure Detection in Sustainable Municipal Waste Management.”
    <i>Journal of Cleaner Production</i>, vol. 336, 130409, Elsevier BV, 2022, doi:<a
    href="https://doi.org/10.1016/j.jclepro.2022.130409">10.1016/j.jclepro.2022.130409</a>.
  short: A. Ebadi Torkayesh, M. Tavana, F.J. Santos-Arteaga, Journal of Cleaner Production
    336 (2022).
date_created: 2024-04-04T15:52:48Z
date_updated: 2024-04-15T13:17:34Z
department:
- _id: '277'
doi: 10.1016/j.jclepro.2022.130409
intvolume: '       336'
keyword:
- Industrial and Manufacturing Engineering
- Strategy and Management
- General Environmental Science
- Renewable Energy
- Sustainability and the Environment
- Building and Construction
language:
- iso: eng
publication: Journal of Cleaner Production
publication_identifier:
  issn:
  - 0959-6526
publication_status: published
publisher: Elsevier BV
status: public
title: A multi-distance interval-valued neutrosophic approach for social failure detection
  in sustainable municipal waste management
type: journal_article
user_id: '51811'
volume: 336
year: '2022'
...
---
_id: '35728'
abstract:
- lang: eng
  text: Technological developments such as Cloud Computing, the Internet of Things,
    Big Data and Artificial Intelligence continue to drive the digital transformation
    of business and society. With the advent of platform-based ecosystems and their
    potential to address complex challenges, there is a trend towards greater interconnectedness
    between different stakeholders to co-create services based on the provision and
    use of data. While previous research on digital transformation mainly focused
    on digital transformation within organizations, it is of growing importance to
    understand the implications for digital transformation on different layers (e.g.,
    interorganizational cooperation and platform ecosystems). In particular, the conceptualization
    and implications of public data spaces and related ecosystems provide promising
    research opportunities. This special issue contains five papers on the topic of
    digital transformation and, with the editorial, further contributes by providing
    an initial conceptualization of public data spaces' potential to foster innovative
    progress and digital transformation from a management perspective.
article_type: letter_note
author:
- first_name: Daniel
  full_name: Beverungen, Daniel
  id: '59677'
  last_name: Beverungen
- first_name: Thomas
  full_name: Hess, Thomas
  last_name: Hess
- first_name: Antonia
  full_name: Köster, Antonia
  last_name: Köster
- first_name: Christiane
  full_name: Lehrer, Christiane
  last_name: Lehrer
citation:
  ama: 'Beverungen D, Hess T, Köster A, Lehrer C. From private digital platforms to
    public data spaces: implications for the digital transformation. <i>Electronic
    Markets</i>. 2022;32:493-501. doi:<a href="https://doi.org/10.1007/s12525-022-00553-z">10.1007/s12525-022-00553-z</a>'
  apa: 'Beverungen, D., Hess, T., Köster, A., &#38; Lehrer, C. (2022). From private
    digital platforms to public data spaces: implications for the digital transformation.
    <i>Electronic Markets</i>, <i>32</i>, 493–501. <a href="https://doi.org/10.1007/s12525-022-00553-z">https://doi.org/10.1007/s12525-022-00553-z</a>'
  bibtex: '@article{Beverungen_Hess_Köster_Lehrer_2022, title={From private digital
    platforms to public data spaces: implications for the digital transformation},
    volume={32}, DOI={<a href="https://doi.org/10.1007/s12525-022-00553-z">10.1007/s12525-022-00553-z</a>},
    journal={Electronic Markets}, publisher={Springer Science and Business Media LLC},
    author={Beverungen, Daniel and Hess, Thomas and Köster, Antonia and Lehrer, Christiane},
    year={2022}, pages={493–501} }'
  chicago: 'Beverungen, Daniel, Thomas Hess, Antonia Köster, and Christiane Lehrer.
    “From Private Digital Platforms to Public Data Spaces: Implications for the Digital
    Transformation.” <i>Electronic Markets</i> 32 (2022): 493–501. <a href="https://doi.org/10.1007/s12525-022-00553-z">https://doi.org/10.1007/s12525-022-00553-z</a>.'
  ieee: 'D. Beverungen, T. Hess, A. Köster, and C. Lehrer, “From private digital platforms
    to public data spaces: implications for the digital transformation,” <i>Electronic
    Markets</i>, vol. 32, pp. 493–501, 2022, doi: <a href="https://doi.org/10.1007/s12525-022-00553-z">10.1007/s12525-022-00553-z</a>.'
  mla: 'Beverungen, Daniel, et al. “From Private Digital Platforms to Public Data
    Spaces: Implications for the Digital Transformation.” <i>Electronic Markets</i>,
    vol. 32, Springer Science and Business Media LLC, 2022, pp. 493–501, doi:<a href="https://doi.org/10.1007/s12525-022-00553-z">10.1007/s12525-022-00553-z</a>.'
  short: D. Beverungen, T. Hess, A. Köster, C. Lehrer, Electronic Markets 32 (2022)
    493–501.
date_created: 2023-01-10T09:52:01Z
date_updated: 2024-04-18T12:37:41Z
ddc:
- '380'
department:
- _id: '526'
doi: 10.1007/s12525-022-00553-z
file:
- access_level: closed
  content_type: application/pdf
  creator: dabe
  date_created: 2024-04-18T12:35:42Z
  date_updated: 2024-04-18T12:35:42Z
  file_id: '53572'
  file_name: EM - From Private Platforms o Pubic Data Spaces.pdf
  file_size: 861383
  relation: main_file
  success: 1
file_date_updated: 2024-04-18T12:35:42Z
has_accepted_license: '1'
intvolume: '        32'
keyword:
- Digital transformation
- Public data spaces
- Digital platforms
- GAIA-X
language:
- iso: eng
page: 493-501
publication: Electronic Markets
publication_identifier:
  issn:
  - 1019-6781
  - 1422-8890
publication_status: published
publisher: Springer Science and Business Media LLC
quality_controlled: '1'
status: public
title: 'From private digital platforms to public data spaces: implications for the
  digital transformation'
type: journal_article
user_id: '59677'
volume: 32
year: '2022'
...
---
_id: '36866'
abstract:
- lang: ger
  text: "Die additive Fertigung bietet die Möglichkeit, digitale Prototypen dank der\r\nBesonderheit
    der werkzeuglosen Fertigung schnellstmöglich in reale Strukturen\r\numzusetzen.
    Dieses Verfahren kann jedoch nur dann mit optimaler Geschwindigkeit\r\ngenutzt
    werden, wenn Engpässe wirksam vermieden werden können. Einer dieser\r\nEngpässe
    ist der Konstruktionsprozess. Gerade im Bereich der additiven Fertigung\r\nsind
    in letzter Zeit immer leistungsfähigere Softwarelösungen erschienen, die das\r\nDesign
    für die additive Fertigung, einschließlich der meisten Computer-Aided-Design\r\n(CAD)-Aufgaben,
    beschleunigen. In vielen Bereichen wird daher bereits versucht, so\r\nviele Schritte
    wie möglich zu automatisieren, nicht selten unter Verwendung\r\nneuronaler Netze
    und künstlicher Intelligenz. Dieser Beitrag zeigt am Beispiel einer\r\nautomatisierten
    Strukturoptimierung eines Stuhls, warum das Nutzen neuronaler\r\nNetze im Konstruktionsprozess
    sinnvoll ist, um die Bereiche der konventionellen\r\nTopologieoptimierung und
    des Generative Design weiter zu verknüpfen und somit die\r\nProduktentwicklungszeit
    zu reduzieren."
author:
- first_name: Manuel
  full_name: Ott, Manuel
  id: '44204'
  last_name: Ott
- first_name: Niclas
  full_name: Meihöfener, Niclas
  last_name: Meihöfener
- first_name: Rainer
  full_name: Koch, Rainer
  last_name: Koch
citation:
  ama: 'Ott M, Meihöfener N, Koch R. Neuronale Netze in der Konstruktion zur Ausschöpfung
    der Potentiale additiver Fertigungstechnologien. In: Deutscher Verband für Materialforschung
    und -prüfung e.V. , ed. <i>Bericht 407 - 7. Tagung des DVM-Arbeitskreises Additiv
    gefertigte Bauteile und Strukturen</i>. Vol 7. Bericht 407 - 7. Tagung des DVM-Arbeitskreises
    Additiv gefertigte Bauteile und Strukturen. ; 2022:91-106. doi:<a href="https://doi.org/10.48447/ADD-2022-014">10.48447/ADD-2022-014</a>'
  apa: Ott, M., Meihöfener, N., &#38; Koch, R. (2022). Neuronale Netze in der Konstruktion
    zur Ausschöpfung der Potentiale additiver Fertigungstechnologien. In Deutscher
    Verband für Materialforschung und -prüfung e.V.  (Ed.), <i>Bericht 407 - 7. Tagung
    des DVM-Arbeitskreises Additiv gefertigte Bauteile und Strukturen</i> (Vol. 7,
    pp. 91–106). <a href="https://doi.org/10.48447/ADD-2022-014">https://doi.org/10.48447/ADD-2022-014</a>
  bibtex: '@inproceedings{Ott_Meihöfener_Koch_2022, place={Berlin}, series={Bericht
    407 - 7. Tagung des DVM-Arbeitskreises Additiv gefertigte Bauteile und Strukturen},
    title={Neuronale Netze in der Konstruktion zur Ausschöpfung der Potentiale additiver
    Fertigungstechnologien}, volume={7}, DOI={<a href="https://doi.org/10.48447/ADD-2022-014">10.48447/ADD-2022-014</a>},
    booktitle={Bericht 407 - 7. Tagung des DVM-Arbeitskreises Additiv gefertigte Bauteile
    und Strukturen}, author={Ott, Manuel and Meihöfener, Niclas and Koch, Rainer},
    editor={Deutscher Verband für Materialforschung und -prüfung e.V. }, year={2022},
    pages={91–106}, collection={Bericht 407 - 7. Tagung des DVM-Arbeitskreises Additiv
    gefertigte Bauteile und Strukturen} }'
  chicago: Ott, Manuel, Niclas Meihöfener, and Rainer Koch. “Neuronale Netze in der
    Konstruktion zur Ausschöpfung der Potentiale additiver Fertigungstechnologien.”
    In <i>Bericht 407 - 7. Tagung des DVM-Arbeitskreises Additiv gefertigte Bauteile
    und Strukturen</i>, edited by Deutscher Verband für Materialforschung und -prüfung
    e.V. , 7:91–106. Bericht 407 - 7. Tagung des DVM-Arbeitskreises Additiv gefertigte
    Bauteile und Strukturen. Berlin, 2022. <a href="https://doi.org/10.48447/ADD-2022-014">https://doi.org/10.48447/ADD-2022-014</a>.
  ieee: 'M. Ott, N. Meihöfener, and R. Koch, “Neuronale Netze in der Konstruktion
    zur Ausschöpfung der Potentiale additiver Fertigungstechnologien,” in <i>Bericht
    407 - 7. Tagung des DVM-Arbeitskreises Additiv gefertigte Bauteile und Strukturen</i>,
    Berlin, 2022, vol. 7, pp. 91–106, doi: <a href="https://doi.org/10.48447/ADD-2022-014">10.48447/ADD-2022-014</a>.'
  mla: Ott, Manuel, et al. “Neuronale Netze in der Konstruktion zur Ausschöpfung der
    Potentiale additiver Fertigungstechnologien.” <i>Bericht 407 - 7. Tagung des DVM-Arbeitskreises
    Additiv gefertigte Bauteile und Strukturen</i>, edited by Deutscher Verband für
    Materialforschung und -prüfung e.V. , vol. 7, 2022, pp. 91–106, doi:<a href="https://doi.org/10.48447/ADD-2022-014">10.48447/ADD-2022-014</a>.
  short: 'M. Ott, N. Meihöfener, R. Koch, in: Deutscher Verband für Materialforschung
    und -prüfung e.V.  (Ed.), Bericht 407 - 7. Tagung des DVM-Arbeitskreises Additiv
    gefertigte Bauteile und Strukturen, Berlin, 2022, pp. 91–106.'
conference:
  end_date: 2022-11-09
  location: Berlin
  name: 7. Tagung des DVM-Arbeitskreises Additiv gefertigte Bauteile und Strukturen
  start_date: 2022-11-08
corporate_editor:
- 'Deutscher Verband für Materialforschung und -prüfung e.V. '
date_created: 2023-01-16T08:42:28Z
date_updated: 2023-01-18T08:52:56Z
department:
- _id: '741'
- _id: '144'
doi: 10.48447/ADD-2022-014
intvolume: '         7'
jel:
- L74
keyword:
- Künstliche Intelligenz
- Neuronale Netze
- 3D-Druck
- Design for Additive Manufacturing
language:
- iso: ger
page: 91-106
place: Berlin
publication: Bericht 407 - 7. Tagung des DVM-Arbeitskreises Additiv gefertigte Bauteile
  und Strukturen
publication_status: published
series_title: Bericht 407 - 7. Tagung des DVM-Arbeitskreises Additiv gefertigte Bauteile
  und Strukturen
status: public
title: Neuronale Netze in der Konstruktion zur Ausschöpfung der Potentiale additiver
  Fertigungstechnologien
type: conference
user_id: '44204'
volume: 7
year: '2022'
...
---
_id: '43156'
abstract:
- lang: eng
  text: The use of mechanical joining technologies offers the possibility of joining
    mixed material structures, which are used in particular in lightweight construction.
    An integrated securing of the joinability in versatile process chains is currently
    hardly possible as the number of combinable tool variants as well as variable
    force- and path-based process parameters is infinite. A versatile process chain,
    i.e. a sequence of all the processes and process steps required for product manufacturing,
    enables targeted changes to the semi-finished product, the joint, the component
    or the joining process that exceed the originally planned extend while still ensuring
    joinability. In detail, it leads to a unique joint with its own mechanical property
    profile, which, against the background of the resulting infinite number of combinations,
    makes it impossible to secure the joinability on the conventional experimentally
    based approach without extensive safety factors. The Transregional Colaborative
    Research Center 285 (TCRC285), which also initiated this special issue, is intended
    to enable mechanical joining technology to be versatile in the sense of high application
    flexibility. This is to be achieved with a numerical representation of the complete
    process chain from the incoming semi finished product via the joining part production
    and the joining process to the property profile of the joint in the operating
    phase. Thus a predictability of the joinability can be achieved and improvements
    in the individual life cycles of a joint can be realized by grasping the cause-and-effect
    relationships. On the basis of this knowledge, new possibilities for intervention
    in the joining process are to be created for the adaptation of the joining processes.
    With the aid of the methods developed for this purpose, tools will later be available
    to the end user to substitute the large number of mechanical joining processes
    or joining task-specific configurations with a smaller number of adaptable processes.
    This expands the flexibility in material choices, enabling challenges in environmental
    issues and sustainability to be overcome.
author:
- first_name: Gerson
  full_name: Meschut, Gerson
  last_name: Meschut
- first_name: Marion
  full_name: Merklein, Marion
  last_name: Merklein
- first_name: Alexander
  full_name: Brosius, Alexander
  last_name: Brosius
- first_name: Mathias
  full_name: Bobbert, Mathias
  last_name: Bobbert
citation:
  ama: Meschut G, Merklein M, Brosius A, Bobbert M. Mechanical joining in versatile
    process chains. <i>Production Engineering</i>. 2022;16(2-3):187-191. doi:<a href="https://doi.org/10.1007/s11740-022-01125-y">10.1007/s11740-022-01125-y</a>
  apa: Meschut, G., Merklein, M., Brosius, A., &#38; Bobbert, M. (2022). Mechanical
    joining in versatile process chains. <i>Production Engineering</i>, <i>16</i>(2–3),
    187–191. <a href="https://doi.org/10.1007/s11740-022-01125-y">https://doi.org/10.1007/s11740-022-01125-y</a>
  bibtex: '@article{Meschut_Merklein_Brosius_Bobbert_2022, title={Mechanical joining
    in versatile process chains}, volume={16}, DOI={<a href="https://doi.org/10.1007/s11740-022-01125-y">10.1007/s11740-022-01125-y</a>},
    number={2–3}, journal={Production Engineering}, publisher={Springer Science and
    Business Media LLC}, author={Meschut, Gerson and Merklein, Marion and Brosius,
    Alexander and Bobbert, Mathias}, year={2022}, pages={187–191} }'
  chicago: 'Meschut, Gerson, Marion Merklein, Alexander Brosius, and Mathias Bobbert.
    “Mechanical Joining in Versatile Process Chains.” <i>Production Engineering</i>
    16, no. 2–3 (2022): 187–91. <a href="https://doi.org/10.1007/s11740-022-01125-y">https://doi.org/10.1007/s11740-022-01125-y</a>.'
  ieee: 'G. Meschut, M. Merklein, A. Brosius, and M. Bobbert, “Mechanical joining
    in versatile process chains,” <i>Production Engineering</i>, vol. 16, no. 2–3,
    pp. 187–191, 2022, doi: <a href="https://doi.org/10.1007/s11740-022-01125-y">10.1007/s11740-022-01125-y</a>.'
  mla: Meschut, Gerson, et al. “Mechanical Joining in Versatile Process Chains.” <i>Production
    Engineering</i>, vol. 16, no. 2–3, Springer Science and Business Media LLC, 2022,
    pp. 187–91, doi:<a href="https://doi.org/10.1007/s11740-022-01125-y">10.1007/s11740-022-01125-y</a>.
  short: G. Meschut, M. Merklein, A. Brosius, M. Bobbert, Production Engineering 16
    (2022) 187–191.
date_created: 2023-03-29T08:31:27Z
date_updated: 2023-03-29T08:32:24Z
department:
- _id: '157'
doi: 10.1007/s11740-022-01125-y
intvolume: '        16'
issue: 2-3
keyword:
- Industrial and Manufacturing Engineering
- Mechanical Engineering
language:
- iso: eng
page: 187-191
publication: Production Engineering
publication_identifier:
  issn:
  - 0944-6524
  - 1863-7353
publication_status: published
publisher: Springer Science and Business Media LLC
status: public
title: Mechanical joining in versatile process chains
type: journal_article
user_id: '53912'
volume: 16
year: '2022'
...
---
_id: '34241'
abstract:
- lang: eng
  text: Due to the increasing use of multi-material constructions and the resulting
    material incompatibilities, mechanical joining technologies are gaining in importance.
    The reasons for this are the variety of joining possibilities as well as high
    load-bearing capacities. However, the currently rigid tooling systems cannot react
    to changing boundary conditions, such as changed sheet thicknesses or strength.
    For this reason, a large number of specialised joining processes have been developed
    to expand the range of applications. Using a versatile self-piercing riveting
    process, multi-material structures are joined in this paper. In this process,
    a modified tool actuator technology is combined with multi-range capable auxiliary
    joining parts. The multi-range capability of the rivets is achieved by forming
    the rivet head onto the respective thickness of the joining part combination without
    creating a tooling set-up effort. The joints are investigated both experimentally
    on the basis of joint formation and load-bearing capacity tests as well as by
    means of numerical simulation. It turned out that all the joints examined could
    be manufactured according to the defined standards. The load-bearing capacities
    of the joints are comparable to those of conventionally joined joints. In some
    cases the joint fails prematurely, which is why lower energy absorptions are obtained.
    However, the maximum forces achieved are higher than those of conventional joints.
    Especially in the case of high-strength materials arranged on the die side, the
    interlock formation is low. In addition, the use of die-sided sheets requires
    a large deformation of the rivet head protrusion, which leads to an increase in
    stress and, as a result, to damage if the rivet head. However, a negative influence
    on the joint load-bearing capacity could be excluded.</jats:p>
author:
- first_name: Fabian
  full_name: Kappe, Fabian
  id: '66459'
  last_name: Kappe
- first_name: Simon
  full_name: Wituschek, Simon
  last_name: Wituschek
- first_name: Mathias
  full_name: Bobbert, Mathias
  id: '7850'
  last_name: Bobbert
- first_name: Michael
  full_name: Lechner, Michael
  last_name: Lechner
- first_name: Gerson
  full_name: Meschut, Gerson
  id: '32056'
  last_name: Meschut
  orcid: 0000-0002-2763-1246
citation:
  ama: Kappe F, Wituschek S, Bobbert M, Lechner M, Meschut G. Joining of multi-material
    structures using a versatile self-piercing riveting process. <i>Production Engineering</i>.
    Published online 2022. doi:<a href="https://doi.org/10.1007/s11740-022-01151-w">10.1007/s11740-022-01151-w</a>
  apa: Kappe, F., Wituschek, S., Bobbert, M., Lechner, M., &#38; Meschut, G. (2022).
    Joining of multi-material structures using a versatile self-piercing riveting
    process. <i>Production Engineering</i>. <a href="https://doi.org/10.1007/s11740-022-01151-w">https://doi.org/10.1007/s11740-022-01151-w</a>
  bibtex: '@article{Kappe_Wituschek_Bobbert_Lechner_Meschut_2022, title={Joining of
    multi-material structures using a versatile self-piercing riveting process}, DOI={<a
    href="https://doi.org/10.1007/s11740-022-01151-w">10.1007/s11740-022-01151-w</a>},
    journal={Production Engineering}, publisher={Springer Science and Business Media
    LLC}, author={Kappe, Fabian and Wituschek, Simon and Bobbert, Mathias and Lechner,
    Michael and Meschut, Gerson}, year={2022} }'
  chicago: Kappe, Fabian, Simon Wituschek, Mathias Bobbert, Michael Lechner, and Gerson
    Meschut. “Joining of Multi-Material Structures Using a Versatile Self-Piercing
    Riveting Process.” <i>Production Engineering</i>, 2022. <a href="https://doi.org/10.1007/s11740-022-01151-w">https://doi.org/10.1007/s11740-022-01151-w</a>.
  ieee: 'F. Kappe, S. Wituschek, M. Bobbert, M. Lechner, and G. Meschut, “Joining
    of multi-material structures using a versatile self-piercing riveting process,”
    <i>Production Engineering</i>, 2022, doi: <a href="https://doi.org/10.1007/s11740-022-01151-w">10.1007/s11740-022-01151-w</a>.'
  mla: Kappe, Fabian, et al. “Joining of Multi-Material Structures Using a Versatile
    Self-Piercing Riveting Process.” <i>Production Engineering</i>, Springer Science
    and Business Media LLC, 2022, doi:<a href="https://doi.org/10.1007/s11740-022-01151-w">10.1007/s11740-022-01151-w</a>.
  short: F. Kappe, S. Wituschek, M. Bobbert, M. Lechner, G. Meschut, Production Engineering
    (2022).
date_created: 2022-12-06T13:50:06Z
date_updated: 2023-04-27T07:53:58Z
department:
- _id: '157'
- _id: '630'
doi: 10.1007/s11740-022-01151-w
keyword:
- Industrial and Manufacturing Engineering
- Mechanical Engineering
language:
- iso: eng
project:
- _id: '130'
  grant_number: '418701707'
  name: 'TRR 285: TRR 285'
- _id: '133'
  name: 'TRR 285 - C: TRR 285 - Project Area C'
- _id: '146'
  name: 'TRR 285 – C02: TRR 285 - Subproject C02'
publication: Production Engineering
publication_identifier:
  issn:
  - 0944-6524
  - 1863-7353
publication_status: published
publisher: Springer Science and Business Media LLC
quality_controlled: '1'
status: public
title: Joining of multi-material structures using a versatile self-piercing riveting
  process
type: journal_article
user_id: '7850'
year: '2022'
...
---
_id: '30100'
abstract:
- lang: eng
  text: Since the application of mechanical joining methods, such as clinching or
    riveting, offers a robust solution for the generation of advanced multi-material
    connections, the use in the field of lightweight designs (e.g. automotive industry)
    is steadily increasing. Therefore, not only the design of an individual joint
    is required but also the dimensioning of the entire joining connection is crucial.
    However, in comparison to thermal joining techniques, such as spot welding, the
    evaluation of the joints’ resistance against defined requirements (e.g. types
    of load, minimal amount of load cycles) mainly relies on the consideration of
    expert knowledge, a few design principles and a small amount of experimental data.
    Since this generally implies the involvement of several domains, such as the material
    characterization or the part design, a tremendous amount of data and knowledge
    is separately generated for a certain dimensioning process. Nevertheless, the
    lack of formalization and standardization in representing the gained knowledge
    leads to a difficult and inconsistent reuse, sharing or searching of already existing
    information. Thus, this contribution presents a specific ontology for the provision
    of cross-domain knowledge about mechanical joining processes and highlights two
    potential use cases of this ontology in the design of clinched and pin joints.</jats:p>
author:
- first_name: Christoph
  full_name: Zirngibl, Christoph
  last_name: Zirngibl
- first_name: Patricia
  full_name: Kügler, Patricia
  last_name: Kügler
- first_name: Julian
  full_name: Popp, Julian
  last_name: Popp
- first_name: Christian Roman
  full_name: Bielak, Christian Roman
  id: '34782'
  last_name: Bielak
- first_name: Mathias
  full_name: Bobbert, Mathias
  id: '7850'
  last_name: Bobbert
- first_name: Dietmar
  full_name: Drummer, Dietmar
  last_name: Drummer
- first_name: Gerson
  full_name: Meschut, Gerson
  id: '32056'
  last_name: Meschut
  orcid: 0000-0002-2763-1246
- first_name: Sandro
  full_name: Wartzack, Sandro
  last_name: Wartzack
- first_name: Benjamin
  full_name: Schleich, Benjamin
  last_name: Schleich
citation:
  ama: Zirngibl C, Kügler P, Popp J, et al. Provision of cross-domain knowledge in
    mechanical joining using ontologies. <i>Production Engineering</i>. Published
    online 2022. doi:<a href="https://doi.org/10.1007/s11740-022-01117-y">10.1007/s11740-022-01117-y</a>
  apa: Zirngibl, C., Kügler, P., Popp, J., Bielak, C. R., Bobbert, M., Drummer, D.,
    Meschut, G., Wartzack, S., &#38; Schleich, B. (2022). Provision of cross-domain
    knowledge in mechanical joining using ontologies. <i>Production Engineering</i>.
    <a href="https://doi.org/10.1007/s11740-022-01117-y">https://doi.org/10.1007/s11740-022-01117-y</a>
  bibtex: '@article{Zirngibl_Kügler_Popp_Bielak_Bobbert_Drummer_Meschut_Wartzack_Schleich_2022,
    title={Provision of cross-domain knowledge in mechanical joining using ontologies},
    DOI={<a href="https://doi.org/10.1007/s11740-022-01117-y">10.1007/s11740-022-01117-y</a>},
    journal={Production Engineering}, publisher={Springer Science and Business Media
    LLC}, author={Zirngibl, Christoph and Kügler, Patricia and Popp, Julian and Bielak,
    Christian Roman and Bobbert, Mathias and Drummer, Dietmar and Meschut, Gerson
    and Wartzack, Sandro and Schleich, Benjamin}, year={2022} }'
  chicago: Zirngibl, Christoph, Patricia Kügler, Julian Popp, Christian Roman Bielak,
    Mathias Bobbert, Dietmar Drummer, Gerson Meschut, Sandro Wartzack, and Benjamin
    Schleich. “Provision of Cross-Domain Knowledge in Mechanical Joining Using Ontologies.”
    <i>Production Engineering</i>, 2022. <a href="https://doi.org/10.1007/s11740-022-01117-y">https://doi.org/10.1007/s11740-022-01117-y</a>.
  ieee: 'C. Zirngibl <i>et al.</i>, “Provision of cross-domain knowledge in mechanical
    joining using ontologies,” <i>Production Engineering</i>, 2022, doi: <a href="https://doi.org/10.1007/s11740-022-01117-y">10.1007/s11740-022-01117-y</a>.'
  mla: Zirngibl, Christoph, et al. “Provision of Cross-Domain Knowledge in Mechanical
    Joining Using Ontologies.” <i>Production Engineering</i>, Springer Science and
    Business Media LLC, 2022, doi:<a href="https://doi.org/10.1007/s11740-022-01117-y">10.1007/s11740-022-01117-y</a>.
  short: C. Zirngibl, P. Kügler, J. Popp, C.R. Bielak, M. Bobbert, D. Drummer, G.
    Meschut, S. Wartzack, B. Schleich, Production Engineering (2022).
date_created: 2022-02-25T07:19:45Z
date_updated: 2023-04-27T07:42:19Z
department:
- _id: '157'
doi: 10.1007/s11740-022-01117-y
keyword:
- Industrial and Manufacturing Engineering
- Mechanical Engineering
language:
- iso: eng
project:
- _id: '130'
  grant_number: '418701707'
  name: 'TRR 285: TRR 285'
- _id: '132'
  name: 'TRR 285 - B: TRR 285 - Project Area B'
- _id: '144'
  name: 'TRR 285 – B05: TRR 285 - Subproject B05'
- _id: '133'
  name: 'TRR 285 - C: TRR 285 - Project Area C'
- _id: '145'
  name: 'TRR 285 – C01: TRR 285 - Subproject C01'
- _id: '131'
  name: 'TRR 285 - A: TRR 285 - Project Area A'
- _id: '135'
  name: 'TRR 285 – A01: TRR 285 - Subproject A01'
publication: Production Engineering
publication_identifier:
  issn:
  - 0944-6524
  - 1863-7353
publication_status: published
publisher: Springer Science and Business Media LLC
quality_controlled: '1'
status: public
title: Provision of cross-domain knowledge in mechanical joining using ontologies
type: journal_article
user_id: '7850'
year: '2022'
...
---
_id: '34244'
author:
- first_name: Fabian
  full_name: Kappe, Fabian
  last_name: Kappe
- first_name: Christoph
  full_name: Zirngibl, Christoph
  last_name: Zirngibl
- first_name: Benjamin
  full_name: Schleich, Benjamin
  last_name: Schleich
- first_name: Mathias
  full_name: Bobbert, Mathias
  last_name: Bobbert
- first_name: Sandro
  full_name: Wartzack, Sandro
  last_name: Wartzack
- first_name: Gerson
  full_name: Meschut, Gerson
  last_name: Meschut
citation:
  ama: Kappe F, Zirngibl C, Schleich B, Bobbert M, Wartzack S, Meschut G. Determining
    the influence of different process parameters on the versatile self-piercing riveting
    process using numerical methods. <i>Journal of Manufacturing Processes</i>. 2022;84:1438-1448.
    doi:<a href="https://doi.org/10.1016/j.jmapro.2022.11.019">10.1016/j.jmapro.2022.11.019</a>
  apa: Kappe, F., Zirngibl, C., Schleich, B., Bobbert, M., Wartzack, S., &#38; Meschut,
    G. (2022). Determining the influence of different process parameters on the versatile
    self-piercing riveting process using numerical methods. <i>Journal of Manufacturing
    Processes</i>, <i>84</i>, 1438–1448. <a href="https://doi.org/10.1016/j.jmapro.2022.11.019">https://doi.org/10.1016/j.jmapro.2022.11.019</a>
  bibtex: '@article{Kappe_Zirngibl_Schleich_Bobbert_Wartzack_Meschut_2022, title={Determining
    the influence of different process parameters on the versatile self-piercing riveting
    process using numerical methods}, volume={84}, DOI={<a href="https://doi.org/10.1016/j.jmapro.2022.11.019">10.1016/j.jmapro.2022.11.019</a>},
    journal={Journal of Manufacturing Processes}, publisher={Elsevier BV}, author={Kappe,
    Fabian and Zirngibl, Christoph and Schleich, Benjamin and Bobbert, Mathias and
    Wartzack, Sandro and Meschut, Gerson}, year={2022}, pages={1438–1448} }'
  chicago: 'Kappe, Fabian, Christoph Zirngibl, Benjamin Schleich, Mathias Bobbert,
    Sandro Wartzack, and Gerson Meschut. “Determining the Influence of Different Process
    Parameters on the Versatile Self-Piercing Riveting Process Using Numerical Methods.”
    <i>Journal of Manufacturing Processes</i> 84 (2022): 1438–48. <a href="https://doi.org/10.1016/j.jmapro.2022.11.019">https://doi.org/10.1016/j.jmapro.2022.11.019</a>.'
  ieee: 'F. Kappe, C. Zirngibl, B. Schleich, M. Bobbert, S. Wartzack, and G. Meschut,
    “Determining the influence of different process parameters on the versatile self-piercing
    riveting process using numerical methods,” <i>Journal of Manufacturing Processes</i>,
    vol. 84, pp. 1438–1448, 2022, doi: <a href="https://doi.org/10.1016/j.jmapro.2022.11.019">10.1016/j.jmapro.2022.11.019</a>.'
  mla: Kappe, Fabian, et al. “Determining the Influence of Different Process Parameters
    on the Versatile Self-Piercing Riveting Process Using Numerical Methods.” <i>Journal
    of Manufacturing Processes</i>, vol. 84, Elsevier BV, 2022, pp. 1438–48, doi:<a
    href="https://doi.org/10.1016/j.jmapro.2022.11.019">10.1016/j.jmapro.2022.11.019</a>.
  short: F. Kappe, C. Zirngibl, B. Schleich, M. Bobbert, S. Wartzack, G. Meschut,
    Journal of Manufacturing Processes 84 (2022) 1438–1448.
date_created: 2022-12-06T13:57:46Z
date_updated: 2023-04-27T08:53:36Z
department:
- _id: '157'
- _id: '630'
doi: 10.1016/j.jmapro.2022.11.019
intvolume: '        84'
keyword:
- Industrial and Manufacturing Engineering
- Management Science and Operations Research
- Strategy and Management
language:
- iso: eng
page: 1438-1448
project:
- _id: '130'
  grant_number: '418701707'
  name: 'TRR 285: TRR 285'
- _id: '133'
  name: 'TRR 285 - C: TRR 285 - Project Area C'
- _id: '146'
  name: 'TRR 285 – C02: TRR 285 - Subproject C02'
- _id: '132'
  name: 'TRR 285 - B: TRR 285 - Project Area B'
- _id: '144'
  name: 'TRR 285 – B05: TRR 285 - Subproject B05'
publication: Journal of Manufacturing Processes
publication_identifier:
  issn:
  - 1526-6125
publication_status: published
publisher: Elsevier BV
quality_controlled: '1'
status: public
title: Determining the influence of different process parameters on the versatile
  self-piercing riveting process using numerical methods
type: journal_article
user_id: '66459'
volume: 84
year: '2022'
...
---
_id: '29208'
abstract:
- lang: eng
  text: The parameters required to calculate the energy efficiency of household refrigerating
    appliances (i.e. refrigerators, freezers and their combinations) are determined
    by standard measurements. According to regulations, these measurements are carried
    out when the appliances are new. It is known from previous studies that various
    technical aging mechanisms can increase electrical energy consumption by up to
    36 % over a product lifespan of 18 years. In order to determine the time dependence
    of the energy consumption of household refrigerating appliances, repeated measurements
    are carried out in this work. Eleven new appliances are examined under standard
    measurement conditions. After just two years of operation, an additional energy
    consumption of up to 11 % is determined. Furthermore, 21 older appliances that
    had previously been measured in new condition are tested again after up to 21
    years of operation. For these older appliances, an average increase of energy
    consumption of 28 % is found. For individual appliances, the maximum increase
    is 36 %. An aging model is developed on the basis of these measurement results,
    which may help to predict the aging-related increase of energy consumption of
    household refrigerating appliances. This model shows an average increase in energy
    consumption of 27 % for an appliance age of 16 years. Supplemental performance
    tests of eight compressors do not show any significant aging effects related to
    these devices after two years of operation. Furthermore, measurements of the thermal
    conductivity of aged polyurethane foam test samples are carried out and an increase
    of its thermal conductivity of 26 % over a period of about three years is determined.
article_number: '117992'
author:
- first_name: Andreas
  full_name: Paul, Andreas
  id: '7828'
  last_name: Paul
- first_name: Elmar
  full_name: Baumhögger, Elmar
  id: '15164'
  last_name: Baumhögger
- first_name: Andreas
  full_name: Elsner, Andreas
  id: '16124'
  last_name: Elsner
- first_name: Michael
  full_name: Reineke, Michael
  id: '24603'
  last_name: Reineke
- first_name: Christian
  full_name: Hueppe, Christian
  last_name: Hueppe
- first_name: Rainer
  full_name: Stamminger, Rainer
  last_name: Stamminger
- first_name: Heike
  full_name: Hoelscher, Heike
  last_name: Hoelscher
- first_name: Hendrik
  full_name: Wagner, Hendrik
  last_name: Wagner
- first_name: Ulrich
  full_name: Gries, Ulrich
  last_name: Gries
- first_name: Wolfgang
  full_name: Becker, Wolfgang
  last_name: Becker
- first_name: Jadran
  full_name: Vrabec, Jadran
  last_name: Vrabec
citation:
  ama: Paul A, Baumhögger E, Elsner A, et al. Impact of aging on the energy efficiency
    of household refrigerating appliances. <i>Applied Thermal Engineering</i>. 2022;205.
    doi:<a href="https://doi.org/10.1016/j.applthermaleng.2021.117992">10.1016/j.applthermaleng.2021.117992</a>
  apa: Paul, A., Baumhögger, E., Elsner, A., Reineke, M., Hueppe, C., Stamminger,
    R., Hoelscher, H., Wagner, H., Gries, U., Becker, W., &#38; Vrabec, J. (2022).
    Impact of aging on the energy efficiency of household refrigerating appliances.
    <i>Applied Thermal Engineering</i>, <i>205</i>, Article 117992. <a href="https://doi.org/10.1016/j.applthermaleng.2021.117992">https://doi.org/10.1016/j.applthermaleng.2021.117992</a>
  bibtex: '@article{Paul_Baumhögger_Elsner_Reineke_Hueppe_Stamminger_Hoelscher_Wagner_Gries_Becker_et
    al._2022, title={Impact of aging on the energy efficiency of household refrigerating
    appliances}, volume={205}, DOI={<a href="https://doi.org/10.1016/j.applthermaleng.2021.117992">10.1016/j.applthermaleng.2021.117992</a>},
    number={117992}, journal={Applied Thermal Engineering}, publisher={Elsevier BV},
    author={Paul, Andreas and Baumhögger, Elmar and Elsner, Andreas and Reineke, Michael
    and Hueppe, Christian and Stamminger, Rainer and Hoelscher, Heike and Wagner,
    Hendrik and Gries, Ulrich and Becker, Wolfgang and et al.}, year={2022} }'
  chicago: Paul, Andreas, Elmar Baumhögger, Andreas Elsner, Michael Reineke, Christian
    Hueppe, Rainer Stamminger, Heike Hoelscher, et al. “Impact of Aging on the Energy
    Efficiency of Household Refrigerating Appliances.” <i>Applied Thermal Engineering</i>
    205 (2022). <a href="https://doi.org/10.1016/j.applthermaleng.2021.117992">https://doi.org/10.1016/j.applthermaleng.2021.117992</a>.
  ieee: 'A. Paul <i>et al.</i>, “Impact of aging on the energy efficiency of household
    refrigerating appliances,” <i>Applied Thermal Engineering</i>, vol. 205, Art.
    no. 117992, 2022, doi: <a href="https://doi.org/10.1016/j.applthermaleng.2021.117992">10.1016/j.applthermaleng.2021.117992</a>.'
  mla: Paul, Andreas, et al. “Impact of Aging on the Energy Efficiency of Household
    Refrigerating Appliances.” <i>Applied Thermal Engineering</i>, vol. 205, 117992,
    Elsevier BV, 2022, doi:<a href="https://doi.org/10.1016/j.applthermaleng.2021.117992">10.1016/j.applthermaleng.2021.117992</a>.
  short: A. Paul, E. Baumhögger, A. Elsner, M. Reineke, C. Hueppe, R. Stamminger,
    H. Hoelscher, H. Wagner, U. Gries, W. Becker, J. Vrabec, Applied Thermal Engineering
    205 (2022).
date_created: 2022-01-10T13:35:45Z
date_updated: 2023-04-27T11:08:36Z
department:
- _id: '728'
- _id: '155'
- _id: '9'
doi: 10.1016/j.applthermaleng.2021.117992
intvolume: '       205'
keyword:
- Industrial and Manufacturing Engineering
- Energy Engineering and Power Technology
language:
- iso: eng
publication: Applied Thermal Engineering
publication_identifier:
  issn:
  - 1359-4311
publication_status: published
publisher: Elsevier BV
quality_controlled: '1'
status: public
title: Impact of aging on the energy efficiency of household refrigerating appliances
type: journal_article
user_id: '7828'
volume: 205
year: '2022'
...
---
_id: '44239'
author:
- first_name: Daokun
  full_name: Dai, Daokun
  last_name: Dai
- first_name: Eugeny Y.
  full_name: Kenig, Eugeny Y.
  id: '665'
  last_name: Kenig
- first_name: Reiner
  full_name: Numrich, Reiner
  last_name: Numrich
citation:
  ama: Dai D, Kenig EY, Numrich R. Experimentelle Untersuchung der Tropfenkondensation
    am chemisch modifizierten Edelstahl‐Drallrohr. <i>Chemie Ingenieur Technik</i>.
    2022;94(6):905-911. doi:<a href="https://doi.org/10.1002/cite.202100176">10.1002/cite.202100176</a>
  apa: Dai, D., Kenig, E. Y., &#38; Numrich, R. (2022). Experimentelle Untersuchung
    der Tropfenkondensation am chemisch modifizierten Edelstahl‐Drallrohr. <i>Chemie
    Ingenieur Technik</i>, <i>94</i>(6), 905–911. <a href="https://doi.org/10.1002/cite.202100176">https://doi.org/10.1002/cite.202100176</a>
  bibtex: '@article{Dai_Kenig_Numrich_2022, title={Experimentelle Untersuchung der
    Tropfenkondensation am chemisch modifizierten Edelstahl‐Drallrohr}, volume={94},
    DOI={<a href="https://doi.org/10.1002/cite.202100176">10.1002/cite.202100176</a>},
    number={6}, journal={Chemie Ingenieur Technik}, publisher={Wiley}, author={Dai,
    Daokun and Kenig, Eugeny Y. and Numrich, Reiner}, year={2022}, pages={905–911}
    }'
  chicago: 'Dai, Daokun, Eugeny Y. Kenig, and Reiner Numrich. “Experimentelle Untersuchung
    Der Tropfenkondensation Am Chemisch Modifizierten Edelstahl‐Drallrohr.” <i>Chemie
    Ingenieur Technik</i> 94, no. 6 (2022): 905–11. <a href="https://doi.org/10.1002/cite.202100176">https://doi.org/10.1002/cite.202100176</a>.'
  ieee: 'D. Dai, E. Y. Kenig, and R. Numrich, “Experimentelle Untersuchung der Tropfenkondensation
    am chemisch modifizierten Edelstahl‐Drallrohr,” <i>Chemie Ingenieur Technik</i>,
    vol. 94, no. 6, pp. 905–911, 2022, doi: <a href="https://doi.org/10.1002/cite.202100176">10.1002/cite.202100176</a>.'
  mla: Dai, Daokun, et al. “Experimentelle Untersuchung Der Tropfenkondensation Am
    Chemisch Modifizierten Edelstahl‐Drallrohr.” <i>Chemie Ingenieur Technik</i>,
    vol. 94, no. 6, Wiley, 2022, pp. 905–11, doi:<a href="https://doi.org/10.1002/cite.202100176">10.1002/cite.202100176</a>.
  short: D. Dai, E.Y. Kenig, R. Numrich, Chemie Ingenieur Technik 94 (2022) 905–911.
date_created: 2023-04-27T16:24:30Z
date_updated: 2023-04-27T16:27:01Z
department:
- _id: '145'
doi: 10.1002/cite.202100176
intvolume: '        94'
issue: '6'
keyword:
- Industrial and Manufacturing Engineering
- General Chemical Engineering
- General Chemistry
language:
- iso: eng
page: 905-911
publication: Chemie Ingenieur Technik
publication_identifier:
  issn:
  - 0009-286X
  - 1522-2640
publication_status: published
publisher: Wiley
quality_controlled: '1'
status: public
title: Experimentelle Untersuchung der Tropfenkondensation am chemisch modifizierten
  Edelstahl‐Drallrohr
type: journal_article
user_id: '90390'
volume: 94
year: '2022'
...
---
_id: '41496'
article_number: '107235'
author:
- first_name: Maxwell
  full_name: Hein, Maxwell
  id: '52771'
  last_name: Hein
  orcid: 0000-0002-3732-2236
- first_name: Nelson Filipe
  full_name: Lopes Dias, Nelson Filipe
  last_name: Lopes Dias
- first_name: David
  full_name: Kokalj, David
  last_name: Kokalj
- first_name: Dominic
  full_name: Stangier, Dominic
  last_name: Stangier
- first_name: Kay-Peter
  full_name: Hoyer, Kay-Peter
  id: '48411'
  last_name: Hoyer
- first_name: Wolfgang
  full_name: Tillmann, Wolfgang
  last_name: Tillmann
- first_name: Mirko
  full_name: Schaper, Mirko
  id: '43720'
  last_name: Schaper
citation:
  ama: Hein M, Lopes Dias NF, Kokalj D, et al. On the influence of physical vapor
    deposited thin coatings on the low-cycle fatigue behavior of additively processed
    Ti-6Al-7Nb alloy. <i>International Journal of Fatigue</i>. 2022;166. doi:<a href="https://doi.org/10.1016/j.ijfatigue.2022.107235">10.1016/j.ijfatigue.2022.107235</a>
  apa: Hein, M., Lopes Dias, N. F., Kokalj, D., Stangier, D., Hoyer, K.-P., Tillmann,
    W., &#38; Schaper, M. (2022). On the influence of physical vapor deposited thin
    coatings on the low-cycle fatigue behavior of additively processed Ti-6Al-7Nb
    alloy. <i>International Journal of Fatigue</i>, <i>166</i>, Article 107235. <a
    href="https://doi.org/10.1016/j.ijfatigue.2022.107235">https://doi.org/10.1016/j.ijfatigue.2022.107235</a>
  bibtex: '@article{Hein_Lopes Dias_Kokalj_Stangier_Hoyer_Tillmann_Schaper_2022, title={On
    the influence of physical vapor deposited thin coatings on the low-cycle fatigue
    behavior of additively processed Ti-6Al-7Nb alloy}, volume={166}, DOI={<a href="https://doi.org/10.1016/j.ijfatigue.2022.107235">10.1016/j.ijfatigue.2022.107235</a>},
    number={107235}, journal={International Journal of Fatigue}, publisher={Elsevier
    BV}, author={Hein, Maxwell and Lopes Dias, Nelson Filipe and Kokalj, David and
    Stangier, Dominic and Hoyer, Kay-Peter and Tillmann, Wolfgang and Schaper, Mirko},
    year={2022} }'
  chicago: Hein, Maxwell, Nelson Filipe Lopes Dias, David Kokalj, Dominic Stangier,
    Kay-Peter Hoyer, Wolfgang Tillmann, and Mirko Schaper. “On the Influence of Physical
    Vapor Deposited Thin Coatings on the Low-Cycle Fatigue Behavior of Additively
    Processed Ti-6Al-7Nb Alloy.” <i>International Journal of Fatigue</i> 166 (2022).
    <a href="https://doi.org/10.1016/j.ijfatigue.2022.107235">https://doi.org/10.1016/j.ijfatigue.2022.107235</a>.
  ieee: 'M. Hein <i>et al.</i>, “On the influence of physical vapor deposited thin
    coatings on the low-cycle fatigue behavior of additively processed Ti-6Al-7Nb
    alloy,” <i>International Journal of Fatigue</i>, vol. 166, Art. no. 107235, 2022,
    doi: <a href="https://doi.org/10.1016/j.ijfatigue.2022.107235">10.1016/j.ijfatigue.2022.107235</a>.'
  mla: Hein, Maxwell, et al. “On the Influence of Physical Vapor Deposited Thin Coatings
    on the Low-Cycle Fatigue Behavior of Additively Processed Ti-6Al-7Nb Alloy.” <i>International
    Journal of Fatigue</i>, vol. 166, 107235, Elsevier BV, 2022, doi:<a href="https://doi.org/10.1016/j.ijfatigue.2022.107235">10.1016/j.ijfatigue.2022.107235</a>.
  short: M. Hein, N.F. Lopes Dias, D. Kokalj, D. Stangier, K.-P. Hoyer, W. Tillmann,
    M. Schaper, International Journal of Fatigue 166 (2022).
date_created: 2023-02-02T14:27:17Z
date_updated: 2023-04-27T16:45:58Z
department:
- _id: '9'
- _id: '158'
doi: 10.1016/j.ijfatigue.2022.107235
intvolume: '       166'
keyword:
- Industrial and Manufacturing Engineering
- Mechanical Engineering
- Mechanics of Materials
- General Materials Science
- Modeling and Simulation
language:
- iso: eng
publication: International Journal of Fatigue
publication_identifier:
  issn:
  - 0142-1123
publication_status: published
publisher: Elsevier BV
quality_controlled: '1'
status: public
title: On the influence of physical vapor deposited thin coatings on the low-cycle
  fatigue behavior of additively processed Ti-6Al-7Nb alloy
type: journal_article
user_id: '43720'
volume: 166
year: '2022'
...
---
_id: '41490'
article_number: '107235'
author:
- first_name: Maxwell
  full_name: Hein, Maxwell
  last_name: Hein
- first_name: Nelson Filipe
  full_name: Lopes Dias, Nelson Filipe
  last_name: Lopes Dias
- first_name: David
  full_name: Kokalj, David
  last_name: Kokalj
- first_name: Dominic
  full_name: Stangier, Dominic
  last_name: Stangier
- first_name: Kay-Peter
  full_name: Hoyer, Kay-Peter
  last_name: Hoyer
- first_name: Wolfgang
  full_name: Tillmann, Wolfgang
  last_name: Tillmann
- first_name: Mirko
  full_name: Schaper, Mirko
  last_name: Schaper
citation:
  ama: Hein M, Lopes Dias NF, Kokalj D, et al. On the influence of physical vapor
    deposited thin coatings on the low-cycle fatigue behavior of additively processed
    Ti-6Al-7Nb alloy. <i>International Journal of Fatigue</i>. 2022;166. doi:<a href="https://doi.org/10.1016/j.ijfatigue.2022.107235">10.1016/j.ijfatigue.2022.107235</a>
  apa: Hein, M., Lopes Dias, N. F., Kokalj, D., Stangier, D., Hoyer, K.-P., Tillmann,
    W., &#38; Schaper, M. (2022). On the influence of physical vapor deposited thin
    coatings on the low-cycle fatigue behavior of additively processed Ti-6Al-7Nb
    alloy. <i>International Journal of Fatigue</i>, <i>166</i>, Article 107235. <a
    href="https://doi.org/10.1016/j.ijfatigue.2022.107235">https://doi.org/10.1016/j.ijfatigue.2022.107235</a>
  bibtex: '@article{Hein_Lopes Dias_Kokalj_Stangier_Hoyer_Tillmann_Schaper_2022, title={On
    the influence of physical vapor deposited thin coatings on the low-cycle fatigue
    behavior of additively processed Ti-6Al-7Nb alloy}, volume={166}, DOI={<a href="https://doi.org/10.1016/j.ijfatigue.2022.107235">10.1016/j.ijfatigue.2022.107235</a>},
    number={107235}, journal={International Journal of Fatigue}, publisher={Elsevier
    BV}, author={Hein, Maxwell and Lopes Dias, Nelson Filipe and Kokalj, David and
    Stangier, Dominic and Hoyer, Kay-Peter and Tillmann, Wolfgang and Schaper, Mirko},
    year={2022} }'
  chicago: Hein, Maxwell, Nelson Filipe Lopes Dias, David Kokalj, Dominic Stangier,
    Kay-Peter Hoyer, Wolfgang Tillmann, and Mirko Schaper. “On the Influence of Physical
    Vapor Deposited Thin Coatings on the Low-Cycle Fatigue Behavior of Additively
    Processed Ti-6Al-7Nb Alloy.” <i>International Journal of Fatigue</i> 166 (2022).
    <a href="https://doi.org/10.1016/j.ijfatigue.2022.107235">https://doi.org/10.1016/j.ijfatigue.2022.107235</a>.
  ieee: 'M. Hein <i>et al.</i>, “On the influence of physical vapor deposited thin
    coatings on the low-cycle fatigue behavior of additively processed Ti-6Al-7Nb
    alloy,” <i>International Journal of Fatigue</i>, vol. 166, Art. no. 107235, 2022,
    doi: <a href="https://doi.org/10.1016/j.ijfatigue.2022.107235">10.1016/j.ijfatigue.2022.107235</a>.'
  mla: Hein, Maxwell, et al. “On the Influence of Physical Vapor Deposited Thin Coatings
    on the Low-Cycle Fatigue Behavior of Additively Processed Ti-6Al-7Nb Alloy.” <i>International
    Journal of Fatigue</i>, vol. 166, 107235, Elsevier BV, 2022, doi:<a href="https://doi.org/10.1016/j.ijfatigue.2022.107235">10.1016/j.ijfatigue.2022.107235</a>.
  short: M. Hein, N.F. Lopes Dias, D. Kokalj, D. Stangier, K.-P. Hoyer, W. Tillmann,
    M. Schaper, International Journal of Fatigue 166 (2022).
date_created: 2023-02-02T14:23:43Z
date_updated: 2023-04-27T16:48:10Z
department:
- _id: '9'
- _id: '158'
doi: 10.1016/j.ijfatigue.2022.107235
intvolume: '       166'
keyword:
- Industrial and Manufacturing Engineering
- Mechanical Engineering
- Mechanics of Materials
- General Materials Science
- Modeling and Simulation
language:
- iso: eng
publication: International Journal of Fatigue
publication_identifier:
  issn:
  - 0142-1123
publication_status: published
publisher: Elsevier BV
status: public
title: On the influence of physical vapor deposited thin coatings on the low-cycle
  fatigue behavior of additively processed Ti-6Al-7Nb alloy
type: journal_article
user_id: '48411'
volume: 166
year: '2022'
...
---
_id: '44236'
article_number: '117097'
author:
- first_name: Marc
  full_name: Wende, Marc
  id: '71302'
  last_name: Wende
- first_name: Christoph
  full_name: Staggenborg, Christoph
  last_name: Staggenborg
- first_name: Eugeny Y.
  full_name: Kenig, Eugeny Y.
  id: '665'
  last_name: Kenig
citation:
  ama: Wende M, Staggenborg C, Kenig EY. Modelling and simulation of zero-gravity
    distillation units with metal foams. <i>Chemical Engineering Science</i>. 2022;247.
    doi:<a href="https://doi.org/10.1016/j.ces.2021.117097">10.1016/j.ces.2021.117097</a>
  apa: Wende, M., Staggenborg, C., &#38; Kenig, E. Y. (2022). Modelling and simulation
    of zero-gravity distillation units with metal foams. <i>Chemical Engineering Science</i>,
    <i>247</i>, Article 117097. <a href="https://doi.org/10.1016/j.ces.2021.117097">https://doi.org/10.1016/j.ces.2021.117097</a>
  bibtex: '@article{Wende_Staggenborg_Kenig_2022, title={Modelling and simulation
    of zero-gravity distillation units with metal foams}, volume={247}, DOI={<a href="https://doi.org/10.1016/j.ces.2021.117097">10.1016/j.ces.2021.117097</a>},
    number={117097}, journal={Chemical Engineering Science}, publisher={Elsevier BV},
    author={Wende, Marc and Staggenborg, Christoph and Kenig, Eugeny Y.}, year={2022}
    }'
  chicago: Wende, Marc, Christoph Staggenborg, and Eugeny Y. Kenig. “Modelling and
    Simulation of Zero-Gravity Distillation Units with Metal Foams.” <i>Chemical Engineering
    Science</i> 247 (2022). <a href="https://doi.org/10.1016/j.ces.2021.117097">https://doi.org/10.1016/j.ces.2021.117097</a>.
  ieee: 'M. Wende, C. Staggenborg, and E. Y. Kenig, “Modelling and simulation of zero-gravity
    distillation units with metal foams,” <i>Chemical Engineering Science</i>, vol.
    247, Art. no. 117097, 2022, doi: <a href="https://doi.org/10.1016/j.ces.2021.117097">10.1016/j.ces.2021.117097</a>.'
  mla: Wende, Marc, et al. “Modelling and Simulation of Zero-Gravity Distillation
    Units with Metal Foams.” <i>Chemical Engineering Science</i>, vol. 247, 117097,
    Elsevier BV, 2022, doi:<a href="https://doi.org/10.1016/j.ces.2021.117097">10.1016/j.ces.2021.117097</a>.
  short: M. Wende, C. Staggenborg, E.Y. Kenig, Chemical Engineering Science 247 (2022).
date_created: 2023-04-27T16:06:49Z
date_updated: 2023-04-28T10:57:47Z
department:
- _id: '145'
doi: 10.1016/j.ces.2021.117097
intvolume: '       247'
keyword:
- Applied Mathematics
- Industrial and Manufacturing Engineering
- General Chemical Engineering
- General Chemistry
language:
- iso: eng
publication: Chemical Engineering Science
publication_identifier:
  issn:
  - 0009-2509
publication_status: published
publisher: Elsevier BV
quality_controlled: '1'
status: public
title: Modelling and simulation of zero-gravity distillation units with metal foams
type: journal_article
user_id: '665'
volume: 247
year: '2022'
...