TY - JOUR AB - In applications of piezoelectric actuators and sensors, the dependability and particularly the reliability throughout their lifetime are vital to manufacturers and end-users and are enabled through condition-monitoring approaches. Existing approaches often utilize impedance measurements over a range of frequencies or velocity measurements and require additional equipment or sensors, such as a laser Doppler vibrometer. Furthermore, the non-negligible effects of varying operating conditions are often unconsidered. To minimize the need for additional sensors while maintaining the dependability of piezoelectric bending actuators irrespective of varying operating conditions, an online diagnostics approach is proposed. To this end, time- and frequency-domain features are extracted from monitored current signals to reflect hairline crack development in bending actuators. For validation of applicability, the presented analysis method was evaluated on piezoelectric bending actuators subjected to accelerated lifetime tests at varying voltage amplitudes and under external damping conditions. In the presence of a crack and due to a diminished stiffness, the resonance frequency decreases and the root-mean-square amplitude of the current signal simultaneously abruptly drops during the lifetime tests. Furthermore, the piezoelectric crack surfaces clapping is reflected in higher harmonics of the current signal. Thus, time-domain features and harmonics of the current signals are sufficient to diagnose hairline cracks in the actuators. AU - Aimiyekagbon, Osarenren Kennedy AU - Bender, Amelie AU - Hemsel, Tobias AU - Sextro, Walter ID - 51518 IS - 3 JF - Electronics KW - piezoelectric transducer KW - self-sensing KW - fault detection KW - diagnostics KW - hairline crack KW - condition monitoring SN - 2079-9292 TI - Diagnostics of Piezoelectric Bending Actuators Subjected to Varying Operating Conditions VL - 13 ER - TY - CHAP AB - This chapter presents a discussion of the concept of agency. Agency is understood as a multifaceted construct describing the idea that human beings make choices, act on these choices, and thereby exercise influence on their own lives as well as their environment. We argue that the concept is discussed from three different perspectives in the literature—transformational, dispositional, and relational—that are each related to learning and development in work contexts. These perspectives do not reflect incompatible positions but rather different aspects of the same phenomena. The chapter also offers an avenue of insight into empirical studies that employ agency as a central concept as well as discussions about concepts that closely overlap with ideas of human beings as agents of power and influence. AU - Goller, Michael AU - Paloniemi, Susanna ID - 30289 KW - Agency Workplace learning Professional development Proactivity Self-direction SN - 2210-5549 T2 - Research Approaches on Workplace Learning TI - Agency: Taking Stock of Workplace Learning Research ER - TY - CHAP AB - The article explores the particular quality of changes introduced through the latest wave of digital transformation of workplaces. It has effects on workflow processes, on distribution of work and tasks, and the mode of distributing working tasks, e.g. through cyber-physical systems. Hence, the changes in work are manifold and require changes in vocational education and training as well as in workplace learning. These changes reveal new challenges for research on workplace learning. Finally, conclusions for future workplace learning research will be developed. AU - Harteis, Christian ID - 30290 KW - Digitalisation Self organisation Distribution of labour Automation SN - 2210-5549 T2 - Research Approaches on Workplace Learning TI - Research on Workplace Learning in Times of Digitalisation ER - TY - CONF AB - To build successful software products, developers continuously have to discover what features the users really need. This discovery can be achieved with continuous experimentation, testing different software variants with distinct user groups, and deploying the superior variant for all users. However, existing approaches do not focus on explicit modeling of variants and experiments, which offers advantages such as traceability of decisions and combinability of experiments. Therefore, our vision is the provision of model-driven continuous experimentation, which provides the developer with a framework for structuring the experimentation process. For that, we introduce the overall concept, apply it to the experimentation on component-based software architectures and point out future research questions. In particular, we show the applicability by combining feature models for modeling the software variants, users, and experiments (i.e., model-driven) with MAPE-K for the adaptation (i.e., continuous experimentation) and implementing the concept based on the component-based Angular framework. AU - Gottschalk, Sebastian AU - Yigitbas, Enes AU - Engels, Gregor ID - 29842 KW - continuous experimentation KW - model-driven KW - component-based software architectures KW - self-adaptation T2 - Proceedings of the 18th International Conference on Software Architecture Companion TI - Model-driven Continuous Experimentation on Component-based Software Architectures ER - TY - JOUR AB - Mit steigenden Optimierungsanforderungen an das Individuum wächst auch das indivi- duelle Bedürfnis nach Kontrolle. Dieses kann u. a. durch self tracking-Technologien erfüllt werden. Anhand von drei Fallbeispielen – der Personenwaage, dem Wearable und dem habit tracker – zeigt dieser Aufsatz, wie sich medienbasierte Selbsttechnologien im historischen Verlauf intensiviert und stärker in den Alltag integriert haben. Ein besonderer Fokus liegt dabei auf der Ambivalenz dieser Medien: Ermöglichen sie auf der einen Seite zwar eine Selbstkontrolle und stellen so potenziell sta- bilisierende Ressourcen für das Individuum dar, schaffen sie auf der anderen Seite auch neue Anforderungen, die es zu erfüllen gilt. AU - Schloots, Franziska Margarete ID - 34614 IS - 7 JF - ffk Journal KW - self-tracking KW - Selbsttechnologien KW - Wearable KW - Bullet Journal KW - Personenwaage KW - Selbstvermessung TI - ‚Understand what’s happening within‘. Selbstkontrolle mit Personenwaage, Wearable und habit tracker VL - 6 ER - TY - JOUR AB - Im Zentrum dieses Beitrags stehen Ergebnisse der Messung pädagogischer Kompetenzen Studierender der Theologie, die das Praxissemester in Deutschland absolviert haben. Das bildungswissenschaftliche Wissen, Kompetenzselbsteinschätzungen und ihre Entwicklung sowie die Einschätzung der im Praxissemester erreichten Ziele Studierender werden dabei unter Berücksichtigung der Ausrichtung des Lehramtsstudiums auf eine Schulform betrachtet. Um die Ergebnisse der Messung bildungswissenschaftlichen Wissens und die der Messung von Kompetenzselbsteinschätzungen zu kontextualisieren (N = 304), wird zuerst die Relevanz des (bildungswissenschaftlichen) Wissens als Ausgangspunkt des Könnens herausgearbeitet. Daran anschließend werden Befunde zur schulformspezifischen Professionalisierung resümiert. Anschließend werden Hypothesen hergeleitet, die Anlage der Studie sowie die Testinstrumente vorge- stellt, die Ergebnisse präsentiert und diskutiert. Die Ergebnisse zeigen wider Erwarten, dass sich weder das bildungswissenschaftliche Wissen, die Kompetenzselbsteinschätzungen und ihre Entwicklung noch die Einschätzung der im Praxissemester erreichten Ziele angehender Lehrkräfte in Abhängigkeit der Schulformen unterscheiden. Die Diskussion bezieht sich u.a. auf die Struktur der Lehramtsstudiengänge, die Denkfiguren zur Entwicklung von Können und die Konzeption der Messinstrumente. AU - Caruso, Carina AU - Seifert, Andreas ID - 35136 IS - 1 JF - Österreichische Religionspädagogische Forum KW - Bildungswissenschaftliches Wissen KW - Kompetenzmessung KW - Kompetenzselbsteinschätzung KW - Praxissemester KW - Professionalisierung / competence measurement KW - competence self-assessment KW - educational knowledge KW - internship KW - professionalization SN - 1018-1539 TI - Inwiefern ist die Professionalisierung in Praxisphasen schulformspezifisch? VL - 30 ER - TY - JOUR AB - Im Zentrum dieses Beitrags stehen Ergebnisse der Messung pädagogischer Kompetenzen Studierender. Dabei werden sowohl das bildungswissenschaftliche Wissen als auch die Entwicklung der Kompe­tenzselbsteinschätzungen in den Bereichen Unterrichten, Erziehen, Beurteilen und Innovieren unter Berücksichtigung individueller Voraussetzungen (Alter, Geschlecht, Abiturnote, Bachelornote, Konfession) betrachtet. Um die Ergeb­nisse hinsichtlich ihrer Bedeutung für die Professionalisierung angehender Lehrkräfte diskutieren zu können, wird, den empirischen Erkenntnissen voranstehend, die Bedeutung von Wissen für berufliches Können herausgearbeitet. Daran anschließend werden Hypothesen hergeleitet, die Anlage der Studie sowie die Testinstrumente vorgestellt, die Ergebnisse präsentiert und diskutiert. Die Ergebnisse zeigen, dass die Abitur- und Bachelornote die Varianz hinsichtlich des pädagogischen Wissens aufklären, sich eine signifikante Entwicklung der Kompetenzselbsteinschätzungen angehender Lehrkräfte feststellen lässt, aber sich angehende Religionslehrkräfte kaum von anderen Studierenden unterscheiden. Die Diskussion nimmt u. a. Rückbezug auf die Denkfiguren zur Entwicklung berufli­chen Könnens und benennt Limitationen, die mit der Studie und Kompetenzmessungen verbunden sind. Daran schließt die Formulierung eines Ausblicks an. Der Beitrag zielt insbesondere darauf, repräsentative Ergebnisse der Kompetenzmessung zu präsentieren und dabei potenzielle Einflussfaktoren auf die studentische Kompetenzent­wicklung zu beleuchten. Ein dadurch angereichertes Konglomerat belastbarer Erkenntnisse zielt darauf, langfristig zur Ableitung lehrerbildungsdidaktischer Überlegungen herangezogen werden zu können, die die studentische Professionalisierung unterstützen. AU - Caruso, Carina AU - Seifert, Andreas ID - 35137 IS - 1 JF - Religionspädagogische Beiträge. Journal for Religion in Education KW - Bildungswissenschaftliches Wissen KW - Kompetenzmessung KW - Kompetenzselbsteinschätzung KW - Praxissemester KW - Professionalisierung / competence measurement KW - competence self-assessment KW - educational knowledge KW - internship KW - professionalization SN - 2750 - 3941 TI - Pädagogische Kompetenz als Ausgangspunkt beruflichen Könnens!? Ergebnisse der Kompetenzmessung angehender Lehrkräfte unter Berücksichtigung individueller Voraussetzungen VL - 45 ER - TY - CONF AB - Theoretical approaches to the transformation towards an inclusive educational system in Germany mostly agree on the involvement of developmental tasks in subject related research (Hinz, 2011). The common understanding of inclusion as a process geared towards equal participation of all children (Booth, 2012) requires a reflexive questioning of established values, attitudes and practices in order to develop inclusive subject related research, teacher training and teaching and learning (Pech & Schomaker, 2013). Among other things, this results in consequences for the design of pre- service teacher training. To a large extent, teacher education is driven by the promotion of central competencies, interests and self-efficacy (Baumert & Kunter, 2011). It aims towards the development and realisation of inclusive interdisciplinary science and social studies (‘Sachunterricht’) in primary education (Moser, 2018). In conjunction with largely acknowledged constructivist approaches to teaching and learning (Möller, 2001), the development of personality, the consideration of basic needs (Deci & Ryan, 1993) and promotion of individual potentials are repeatedly fundamentally represented in subject related and pedagogical considerations (Feuser, 1989; GDSU, 2013). Therefore, the aforementioned constructivist approach is connected to several certain key paradigms for teaching and learning processes (e.g., Vygotskij, 1978; Posner et al., 1982; van de Pol et al., 2010). In this regard, the nature of primary school students’ basic needs have empirically not been sufficiently studied yet. Theoretical frameworks from motivational psychology (Deci & Ryan, 1993) do not explicitly address how individual needs differ and how the diversity of needs can be included in joint-learning, multi-perspective technology education classes. The research project the present paper is part of aims to develop a research-based concept for the professionalisation of pre-service teachers in a seminar course. Therefore, the promotion of the pre- service teachers’ interests and self-efficacy expectations have been assessed in a pre-post research design with a control group visiting another course not related to technology education and inclusion. The present paper describes and discusses first results of the project and will give an outlook on subsequent developmental tasks. AU - Schröer, Franz AU - Tenberge, Claudia ED - Gill, David ED - Tuff, Jim ED - Kennedy, Thomas ED - Pendergast, Shawn ED - Jamil, Sana ID - 40046 KW - Inclusion KW - basic needs KW - pre-service teacher training KW - interest KW - self-efficacy T2 - PATT39 - PATT on the Edge Technology, Innovation and Education TI - How to enable pre-service teachers to design technological teaching and learning inclusively? – On the nature and consideration of basic needs in teacher training ER - TY - JOUR AU - Constantiou, Ioanna AU - Mukkamala, Alivelu AU - Sjöklint, Mimmi AU - Trier, Matthias ID - 36083 JF - European Journal of Information Systems KW - Library and Information Sciences KW - Information Systems KW - Self-Tracking KW - User Behaviour KW - Discontinuance SN - 0960-085X TI - Engaging with self-tracking applications: how do users respond to their performance data? ER - TY - JOUR AB - The family plays an important role in adolescents’ social development. Yet there is little information about the impact of family climate on adolescents’ social adaptation, and the term “family climate” is seldom clearly defined and is usually related to other concepts, such as family systems or family environments. To understand the core of family climate, this study conducted a systematic review to analyze research about family climate associated with adolescents’ social adaptation in community samples. A search of empirical research published over the last 20 years identified 12 relevant studies. The studies revealed that family climate can mainly be described in terms of cohesion, conflict, organization, adaptability, and expressiveness. Family climate was shown to be a good predictor of both problem-solving skills and violence in relationships and exhibited further associations with other aspects of social adaptation. This review revealed a need for more systematic and longitudinal research on family climate in community samples. AU - Kurock, Ricarda AU - Gruchel, Nicole AU - Bonanati, Sabrina AU - Buhl, Heike M. ID - 32565 JF - Adolescent Research Review KW - Family environment KW - Family system KW - Adolescents KW - Social adaptation KW - Systematic review SN - 2363-8346 TI - Family Climate and Social Adaptation of Adolescents in Community Samples: A Systematic Review ER - TY - JOUR AB - Modern services consist of interconnected components,e.g., microservices in a service mesh or machine learning functions in a pipeline. These services can scale and run across multiple network nodes on demand. To process incoming traffic, service components have to be instantiated and traffic assigned to these instances, taking capacities, changing demands, and Quality of Service (QoS) requirements into account. This challenge is usually solved with custom approaches designed by experts. While this typically works well for the considered scenario, the models often rely on unrealistic assumptions or on knowledge that is not available in practice (e.g., a priori knowledge). We propose DeepCoord, a novel deep reinforcement learning approach that learns how to best coordinate services and is geared towards realistic assumptions. It interacts with the network and relies on available, possibly delayed monitoring information. Rather than defining a complex model or an algorithm on how to achieve an objective, our model-free approach adapts to various objectives and traffic patterns. An agent is trained offline without expert knowledge and then applied online with minimal overhead. Compared to a state-of-the-art heuristic, DeepCoord significantly improves flow throughput (up to 76%) and overall network utility (more than 2x) on realworld network topologies and traffic traces. It also supports optimizing multiple, possibly competing objectives, learns to respect QoS requirements, generalizes to scenarios with unseen, stochastic traffic, and scales to large real-world networks. For reproducibility and reuse, our code is publicly available. AU - Schneider, Stefan Balthasar AU - Khalili, Ramin AU - Manzoor, Adnan AU - Qarawlus, Haydar AU - Schellenberg, Rafael AU - Karl, Holger AU - Hecker, Artur ID - 21808 JF - Transactions on Network and Service Management KW - network management KW - service management KW - coordination KW - reinforcement learning KW - self-learning KW - self-adaptation KW - multi-objective TI - Self-Learning Multi-Objective Service Coordination Using Deep Reinforcement Learning ER - TY - GEN AB - Macrodiversity is a key technique to increase the capacity of mobile networks. It can be realized using coordinated multipoint (CoMP), simultaneously connecting users to multiple overlapping cells. Selecting which users to serve by how many and which cells is NP-hard but needs to happen continuously in real time as users move and channel state changes. Existing approaches often require strict assumptions about or perfect knowledge of the underlying radio system, its resource allocation scheme, or user movements, none of which is readily available in practice. Instead, we propose three novel self-learning and self-adapting approaches using model-free deep reinforcement learning (DRL): DeepCoMP, DD-CoMP, and D3-CoMP. DeepCoMP leverages central observations and control of all users to select cells almost optimally. DD-CoMP and D3-CoMP use multi-agent DRL, which allows distributed, robust, and highly scalable coordination. All three approaches learn from experience and self-adapt to varying scenarios, reaching 2x higher Quality of Experience than other approaches. They have very few built-in assumptions and do not need prior system knowledge, making them more robust to change and better applicable in practice than existing approaches. AU - Schneider, Stefan Balthasar AU - Karl, Holger AU - Khalili, Ramin AU - Hecker, Artur ID - 33854 KW - mobility management KW - coordinated multipoint KW - CoMP KW - cell selection KW - resource management KW - reinforcement learning KW - multi agent KW - MARL KW - self-learning KW - self-adaptation KW - QoE TI - DeepCoMP: Coordinated Multipoint Using Multi-Agent Deep Reinforcement Learning ER - TY - JOUR AB - With the rapid progress of technological development, self-efficacy in reference to digital devices (i.e., information and computer technology [ICT] self-efficacy) is an important driver that helps students to deal with technological problems and support their lifelong learning processes. Schools, peers, and home learning environments are important sources for the development of positive self-efficacy. Expanding on previous research, we investigated the associations between different aspects of the digital home learning environment and students’ ICT self-efficacy. The moderation effects of gender were also tested. A total of 651 children answered a questionnaire about different digital home learning environment dimensions and estimated their ICT self-efficacy using an adapted scale—Schwarzer and Jerusalem’s (1999) general self-efficacy scale. Using the structural equation modeling technique, a digital home learning environment containing six different qualities of parental support was investigated. Families’ cultural capital, parents’ attitudes toward the Internet, and shared Internet activities at home contributed positively to ICT self-efficacy. We observed small gender differences, with the moderation effect being nonsignificant. The results help researchers and practitioners to understand how different dimensions of the digital home learning environment support ICT self-efficacy. We will discuss how parents can enhance the home learning environment and how teachers can integrate this knowledge into formal education. AU - Bonanati, Sabrina AU - Buhl, Heike M. ID - 32558 IS - 2 JF - Learning Environments Research KW - Digital media use KW - Gender KW - Home learning environment KW - ICT self-efcacy KW - Motivation KW - Parental involvement SN - 1387-1579 TI - The digital home learning environment and its relation to children’s ICT self-efficacy VL - 25 ER - TY - GEN AB - This study examines the relation between voluntary audit and the cost of debt in private firms. We use a sample of 4,058 small private firms operating in the period 2006‐2017 that are not subject to mandatory audits. Firms decide for a voluntary audit of financial statements either because the economic setting in which they operate effectively forces them to do so (e.g., ownership complexity, export‐oriented supply chain, subsidiary status) or because firm fundamentals and/or financial reporting practices limit their access to financial debt, both reflected in earnings quality. We use these factors to model the decision for voluntary audit. In the outcome analyses, we find robust evidence that voluntary audits are associated with higher, rather than lower, interest rate by up to 3.0 percentage points. This effect is present regardless of the perceived audit quality (Big‐4 vs. non‐Big‐4), but is stronger for non‐Big‐4 audits where auditees have a stronger position relative to auditors. Audited firms’ earnings are less informative about future operating performance relative to unaudited counterparts. We conclude that voluntary audits facilitate access to financial debt for firms with higher risk that may otherwise have no access to this form of financing. The price paid is reflected in higher interest rates charged to firms with voluntary audits – firms with higher information and/or fundamental risk. AU - Ichev, Riste AU - Koren, Jernej AU - Kosi, Urska AU - Sitar Sustar, Katarina AU - Valentincic, Aljosa ID - 37136 KW - private firms KW - voluntary audit KW - cost of debt KW - self‐selection bias KW - risk TI - Cost of Debt for Private Firms Revisited: Voluntary Audits as a Reflection of Risk ER - TY - CHAP AB - Self-piercing riveting is an established technique for joining multi-material structures in car body manufacturing. Rivets for self-piercing riveting differ in their geometry, the material used, the condition of the material and their surface condition. To shorten the manufacturing process by omitting the heat treatment and the coating process, the authors have elaborated a concept for the use of stainless steel with high strain hardening as a rivet material. The focus of the present investigation is on the evaluation of the influences of the rivet’s geometry and material on its deformation behaviour. Conventional rivets of types P and HD2, a rivet with an improved geometry made of treatable steel 38B2, and rivets made of the stainless steels 1.3815 and 1.4541 are examined. The analysis is conducted by means of multi-step joining tests for two material combinations comprising high-strength steel HCT70X and aluminium EN AW-5083. The joints are cut to provide a cross-section and the deformation behaviour of the different rivets is analysed on the basis of the measured changes in geometry and hardness. In parallel, an examination of the force-stroke curves provides further insights. It can be demonstrated that, besides the geometry, the material strength, in particular, has a significant influence on the deformation behaviour of the rivet. The strength of steel 1.4541 is seen to be too low for the joining task, while the strength of steel 1.3815 is sufficient, and hence the investigation confirms the capability of rivets made of 1.3815 for joining even challenging material combinations. AU - Uhe, Benedikt AU - Kuball, Clara-Maria AU - Merklein, Marion AU - Meschut, Gerson ED - Daehn, Glenn ED - Cao, Jian ED - Kinsey, Brad ED - Tekkaya, Erman ED - Vivek, Anupam ED - Yoshida, Yoshinori ID - 22930 KW - Self-piercing riveting KW - Lightweight design KW - Deformation behaviour KW - Stainless steel KW - High nitrogen steel T2 - Forming the Future - Proceedings of the 13th International Conference on the Technology of Plasticity. The Minerals, Metals & Materials Series. TI - Self-Piercing Riveting Using Rivets Made of Stainless Steel with High Strain Hardening ER - TY - CONF AB - The use of high-strength steel and aluminium is rising due to the intensified efforts being made in lightweight design, and self-piercing riveting is becoming increasingly important. Conventional rivets for self-piercing riveting differ in their geometry, the material used, the condition of the material and the coating. To shorten the manufacturing process, the use of stainless steel with high strain hardening as the rivet material represents a promising approach. This allows the coating of the rivets to be omitted due to the corrosion resistance of the material and, since the strength of the stainless steel is achieved by cold forming, heat treatment is no longer required. In addition, it is possible to adjust the local strength within the rivet. Because of that, the authors have elaborated a concept for using high nitrogen steel 1.3815 as the rivet material. The present investigation focusses on the joint strength in order to evaluate the capability of rivets in high nitrogen steel by comparison to conventional rivets made of treatable steel. Due to certain challenges in the forming process of the high nitrogen steel rivets, deviations result from the targeted rivet geometry. Mainly these deviations cause a lower joint strength with these rivets, which is, however, adequate. All in all, the capability of the new rivet is proven by the results of this investigation. AU - Uhe, Benedikt AU - Kuball, Clara-Maria AU - Merklein, Marion AU - Meschut, Gerson ID - 22274 KW - Self-piercing Riveting KW - Joining Technology KW - Rivet Geometry KW - Rivet Material KW - High Nitrogen Steel KW - Joint Strength TI - Strength of self-piercing riveted Joints with conventional Rivets and Rivets made of High Nitrogen Steel ER - TY - CONF AB - Modern services comprise interconnected components, e.g., microservices in a service mesh, that can scale and run on multiple nodes across the network on demand. To process incoming traffic, service components have to be instantiated and traffic assigned to these instances, taking capacities and changing demands into account. This challenge is usually solved with custom approaches designed by experts. While this typically works well for the considered scenario, the models often rely on unrealistic assumptions or on knowledge that is not available in practice (e.g., a priori knowledge). We propose a novel deep reinforcement learning approach that learns how to best coordinate services and is geared towards realistic assumptions. It interacts with the network and relies on available, possibly delayed monitoring information. Rather than defining a complex model or an algorithm how to achieve an objective, our model-free approach adapts to various objectives and traffic patterns. An agent is trained offline without expert knowledge and then applied online with minimal overhead. Compared to a state-of-the-art heuristic, it significantly improves flow throughput and overall network utility on real-world network topologies and traffic traces. It also learns to optimize different objectives, generalizes to scenarios with unseen, stochastic traffic patterns, and scales to large real-world networks. AU - Schneider, Stefan Balthasar AU - Manzoor, Adnan AU - Qarawlus, Haydar AU - Schellenberg, Rafael AU - Karl, Holger AU - Khalili, Ramin AU - Hecker, Artur ID - 19609 KW - self-driving networks KW - self-learning KW - network coordination KW - service coordination KW - reinforcement learning KW - deep learning KW - nfv T2 - IEEE International Conference on Network and Service Management (CNSM) TI - Self-Driving Network and Service Coordination Using Deep Reinforcement Learning ER - TY - GEN AB - The aim to reduce pollutant emission has led to a trend towards lightweight construction in car body development during the last years. As a consequence of the resulting need for multi-material design, mechanical joining technologies become increasingly important. Mechanical joining allows for the combination of dissimilar materials, while thermic joining techniques reach their limits. Self-piercing riveting enables the joining of dissimilar materials by using semi-tubular rivets as mechanical fasteners. The rivet production, however, is costly and time-consuming, as the rivets generally have to be hardened, tempered and coated after forming, in order to achieve an adequate strength and corrosion resistance. A promising approach to improve the efficiency of the rivet manufacturing is the use of high-strength high nitrogen steel as rivet material because these additional process steps would not be necessary anymore. As a result of the comparatively high nitrogen content, such steels have various beneficial properties like higher strength, good ductility and improved corrosion resistance. By cold bulk forming of high nitrogen steels high-strength parts can be manufactured due to the strengthening which is caused by the high strain hardening. However, high tool loads thereby have to be expected and are a major challenge during the production process. Consequently, there is a need for appropriate forming strategies. This paper presents key aspects concerning the process design for the manufacturing of semi-tubular self-piercing rivets made of high-strength steel. The aim is to produce the rivets in several forming stages without intermediate heat treatment between the single stages. Due to the high strain hardening of the material, a two stage forming concept will be investigated. Cup-backward extrusion is chosen as the first process step in order to form the rivet shank without forming the rivet foot. Thus, the strain hardening effects in the area of the rivet foot are minimized and the tool loads during the following process step can be reduced. During the second and final forming stage the detailed geometry of the rivet foot and the rivet head is formed. In this context, the effect of different variations, for example concerning the final geometry of the rivet foot, on the tool load is investigated using multistage numerical analysis. Furthermore, the influence of the process temperature on occurring stresses is analysed. Based on the results of the investigations, an adequate forming strategy and a tool concept for the manufacturing of semi-tubular self-piercing rivets made of high-strength steel are presented. ED - Kuball, Clara-Maria ED - Uhe, Benedikt ED - Meschut, Gerson ED - Merklein, Marion ID - 19976 KW - high nitrogen steel KW - self-piercing riveting KW - joining by forming KW - bulk forming KW - tool design TI - Process design for the forming of semi-tubular self-piercing rivets made of high nitrogen steel VL - 50 ER - TY - CONF AB - Augmented Reality (AR) has recently found high attention in mobile shopping apps such as in domains like furniture or decoration. Here, the developers of the apps focus on the positioning of atomic 3D objects in the physical environment. With this focus, they neglect the configuration of multi-faceted 3D object composition according to the user needs and environmental constraints. To tackle these challenges, we present a model-based approach to support AR-assisted product con-figuration based on the concept of Dynamic Software Product Lines. Our approach splits products (e.g. table) into parts (e.g. tabletop, ta-ble legs, funnier) with their 3D objects and additional information (e.g. name, price). The possible products, which can be configured out of these parts, are stored in a feature model. At runtime, this feature model can be used to configure 3D object compositions out of the product parts and adapt to user needs and environmental constraints. The benefits of this approach are demonstrated by a case study of configuring modular kitchens with the help of a prototypical mobile-based implementation. AU - Gottschalk, Sebastian AU - Yigitbas, Enes AU - Schmidt, Eugen AU - Engels, Gregor ED - Bernhaupt, Regina ED - Ardito, Carmelo ED - Sauer, Stefan ID - 18249 KW - Product Configuration KW - Augmented Reality KW - Runtime Adaptation KW - Dynamic Software Product Lines T2 - Human-Centered Software Engineering. HCSE 2020 TI - Model-based Product Configuration in Augmented Reality Applications VL - 12481 ER - TY - CONF AB - The continuous innovation of its business models is an important task for a company to stay competitive. During this process, the company has to validate various hypotheses about its business models by adapting to uncertain and changing customer needs effectively and efficiently. This adaptation, in turn, can be supported by the concept of Software Product Lines (SPLs). SPLs reduce the time to market by deriving products for customers with changing requirements using a common set of features, structured as a feature model. Analogously, we support the process of business model adaptation by applying the engineering process of SPLs to the structure of the Business Model Canvas (BMC). We call this concept a Business Model Decision Line (BMDL). The BMDL matches business domain knowledge in the form of a feature model with customer needs to derive hypotheses about the business model together with experiments for validation. Our approach is effective by providing a comprehensive overview of possible business model adaptations and efficient by reusing experiments for different hypotheses. We implement our approach in a tool and illustrate the usefulness with an example of developing business models for a mobile application. AU - Gottschalk, Sebastian AU - Rittmeier, Florian AU - Engels, Gregor ID - 16933 KW - Business Model Decision Line KW - Business Model Adaptation KW - Hypothesis-driven Adaptation KW - Software Product Line KW - Feature Model T2 - Proceedings of the 22nd IEEE International Conference on Business Informatics TI - Hypothesis-driven Adaptation of Business Models based on Product Line Engineering ER - TY - CONF AB - To build successful products, the developers have to adapt their product features and business models to uncertain customer needs. This adaptation is part of the research discipline of Hypotheses Engineering (HE) where customer needs can be seen as hypotheses that need to be tested iteratively by conducting experiments together with the customer. So far, modeling support and associated traceability of this iterative process are missing. Both, in turn, are important to document the adaptation to the customer needs and identify experiments that provide most evidence to the customer needs. To target this issue, we introduce a model-based HE approach with a twofold contribution: First, we develop a modeling language that models hypotheses and experiments as interrelated hierarchies together with a mapping between them. While the hypotheses are labeled with a score level of their current evidence, the experiments are labeled with a score level of maximum evidence that can be achieved during conduction. Second, we provide an iterative process to determine experiments that offer the most evidence improvement to the modeled hypotheses. We illustrate the usefulness of the approach with an example of testing the business model of a mobile application. AU - Gottschalk, Sebastian AU - Yigitbas, Enes AU - Engels, Gregor ED - Shishkov, Boris ID - 16934 KW - Hypothesis Engineering KW - Model-based KW - Customer Need Adaptation KW - Business Model KW - Product Features T2 - Business Modeling and Software Design TI - Model-based Hypothesis Engineering for Supporting Adaptation to Uncertain Customer Needs VL - 391 ER - TY - JOUR AU - Otroshi, Mortaza AU - Rossel, Moritz AU - Meschut, Gerson ID - 20143 JF - Journal of Advanced Joining Processes KW - Self-pierce riveting KW - Ductile fracture KW - Damage modeling KW - GISSMO damage model TI - Stress state dependent damage modeling of self-pierce riveting process simulation using GISSMO damage model VL - 1 ER - TY - JOUR AB - Im Artikel werden drei verschiedene Lernzugänge (kom-petenzorientiertes, ästhetisches und biographisches Lernen) vorgestellt und aus theoretischer Perspektive deren motivierender Gehalt für selbstreguliertes Lernen in Praxisphasen des Lehramtsstudiumsherausgearbeitet. Als theoretische Grund-lage dient die Selbstbestimmungstheorie als zentrale motivationale Theorie zur Erklärung selbstbestimmten Handelns. AU - Caruso, Carina AU - Adammek, Christine AU - Bonanati, Sabrina AU - Wiescholek, Sybille ID - 35298 IS - 1 JF - Herausforderung Lehrer*innenbildung - Zeitschrift Zur Konzeption, Gestaltung Und Diskussion KW - ästhetische Forschung KW - Biographiearbeit KW - Praxissemester KW - Professionalisierung KW - selbstreguliertes Lernen KW - Motivation / aesthetic research KW - biographical work KW - long-term internship KW - profes-sionalization KW - self-regulated learning KW - motivation SN - 2625-0675 TI - Motivierende Lernzugänge als Ausgangspunkt der Professionalisierung angehender Lehrer_innen VL - 3 ER - TY - GEN AB - Due to the trend towards lightweight design in car body development mechanical joining technologies become increasingly important. These techniques allow for the joining of dissimilar materials and thus enable multi-material design, while thermic joining methods reach their limits. Semi-tubular self-piercing riveting is an important mechanical joining technology. The rivet production, however, is costly and time-consuming, as the process consists of several process steps including the heat treatment and coating of the rivets in order to achieve an adequate strength and corrosion resistance. The use of high nitrogen steel as rivet material leads to the possibility of reducing process steps and hence increasing the efficiency of the process. However, the high tool loads being expected due to the high strain hardening of the material are a major challenge during the rivet production. Thus, there is a need for appropriate forming strategies, such as the manufacturing of the rivets at elevated temperatures. Prior investigations led to the conclusion that forming already at 200 °C results in a distinct reduction of the yield strength. To create a deeper understanding of the forming behaviour of high nitrogen steel at elevated temperatures, compression tests were conducted in a temperature range between room temperature and 200 °C. The determined true stress – true strain curves are the basis for the further process and tool design of the rivet production. Another key factor for the rivet manufacturing at elevated temperatures is the influence of the process temperature on the tribological conditions. For this reason, ring compression tests at room temperature and 200 °C are carried out. The friction factors are determined on the basis of calibration curves resulting from the numerical analysis of the ring compression process. The investigations indicate that the friction factor at 200 °C is significantly higher compared to room temperature. This essential fact has to be taken into account for the process and tool design for the rivet production using high nitrogen steel. ED - Kuball, Clara-Maria ED - Jung, R ED - Uhe, Benedikt ED - Meschut, Gerson ED - Merklein, Marion ID - 19974 KW - High nitrogen steel KW - Self-piercing riveting KW - Joining by forming KW - Bulk forming KW - Strain hardening TI - Influence of the process temperature on the forming behaviour and the friction during bulk forming of high nitrogen steel VL - 1 ER - TY - JOUR AB - As a result of lightweight design, increased use is being made of high-strength steel and aluminium in car bodies. Self-piercing riveting is an established technique for joining these materials. The dissimilar properties of the two materials have led to a number of different rivet geometries in the past. Each rivet geometry fulfils the requirements of the materials within a limited range. In the present investigation, an improved rivet geometry is developed, which permits the reliable joining of two material combinations that could only be joined by two different rivet geometries up until now. Material combination 1 consists of high-strength steel on both sides, while material combination 2 comprises aluminium on the punch side and high-strength steel on the die side. The material flow and the stress and strain conditions prevailing during the joining process are analysed by means of numerical simulation. The rivet geometry is then improved step-by-step on the basis of this analysis. Finally, the improved rivet geometry is manufactured and the findings of the investigation are verified in experimental joining tests. AU - Uhe, Benedikt AU - Kuball, Clara-Maria AU - Merklein, Marion AU - Meschut, Gerson ID - 19973 JF - Production Engineering KW - Self-piercing riveting KW - Joining technology KW - Rivet geometry KW - Multi-material design KW - High-strength steel KW - Aluminium TI - Improvement of a rivet geometry for the self-piercing riveting of high-strength steel and multi-material joints VL - 14 ER - TY - THES AB - Ultraschall wird zur Effizienzsteigerung in verfahrenstechnischen Prozessen eingesetzt. Die Betriebsparamter der Ultraschallsysteme werden empirisch ermittelt, da derzeit keine systematische Analyse der Wechselwirkung zwischen Ultraschallwandler und Schallfeld sowie kein Verfahren zur Messung der Kavitationsaktivität ohne zusätzlichen Sensor existieren. Auf Basis einer experimentellen Analyse des betrachteten sonochemischen Reaktors wird ein Finite-Elemente-Modell aufgebaut, das die Wechselwirkung zwischen Schallfeld und Ultraschallwandler berücksichtigt. Die modellbasierte Analyse zeigt, dass wegen der akustischen Eigenschaften des Autoklavs nur direkt an der Sonotrode Kavitation entsteht. Die Wechselwirkung zwischen Ultraschallwandler und Schallfeld ermöglicht Aussagen über das Schallfeld und die Kavitationsaktivität auf Basis der Rückwirkung auf den Ultraschallwandler. Die lineare Schalldruckverteilung ermöglicht eine Prognose über die Verteilung von Kavitationszonen. Das beschriebene Modell liefert wertvolle Erkenntnisse für die Auslegung, Analyse und Skalierung sonochemischer Reaktoren. Auf Grund der rauen Prozessrandbedingungen ist die Applikation von Sensoren zur Überwachung der Kavitationsaktivität in vielen sonochemischen Prozessen nicht möglich. Zur prozessbegleitenden Messung der Kavitationsaktivität wird ein Verfahren entwickelt, das die Bewertung der Kavitationsaktivität durch Auswertung der Rückwirkung auf den Ultraschallwandler erlaubt. Das Messverfahren ermöglicht eine vorhersagbare und reproduzierbare Durchführung kavitationsbasierter Prozesse und stellt eine wichtige Erweiterung für bestehende und neue Ultraschallsysteme dar. AU - Bornmann, Peter ID - 10000 KW - Sonochemie KW - Akustische Kavitation KW - Kavitationsmessung KW - Kavitationsdetektion KW - FEM-Simulation Ultraschallwandler KW - Prozessüberwachung KW - FEM-Simulation Schallfeld KW - Self-Sensing KW - Piezoelektrische Ultraschallwandler KW - Ultraschallreinigung TI - Modellierung und experimentelle Charakterisierung der Wechselwirkung zwischen Ultraschallwandler und Flüssigkeit in kavitationsbasierten Prozessen ER - TY - CONF AB - In this paper we present two major results: First, we introduce the first self-stabilizing version of a supervised overlay network (as introduced in~\cite{DBLP:conf/ispan/KothapalliS05}) by presenting a self-stabilizing supervised skip ring. Secondly, we show how to use the self-stabilizing supervised skip ring to construct an efficient self-stabilizing publish-subscribe system. That is, in addition to stabilizing the overlay network, every subscriber of a topic will eventually know all of the publications that have been issued so far for that topic. The communication work needed to processes a subscribe or unsubscribe operation is just a constant in a legitimate state, and the communication work of checking whether the system is still in a legitimate state is just a constant on expectation for the supervisor as well as any process in the system. AU - Feldmann, Michael AU - Kolb, Christina AU - Scheideler, Christian AU - Strothmann, Thim Frederik ID - 1163 KW - Topological Self-stabilization KW - Supervised Overlay KW - Publish-Subscribe System T2 - Proceedings of the 32nd IEEE International Parallel & Distributed Processing Symposium (IPDPS) TI - Self-Stabilizing Supervised Publish-Subscribe Systems ER - TY - CONF AB - While a lot of research in distributed computing has covered solutions for self-stabilizing computing and topologies, there is far less work on self-stabilization for distributed data structures. Considering crashing peers in peer-to-peer networks, it should not be taken for granted that a distributed data structure remains intact. In this work, we present a self-stabilizing protocol for a distributed data structure called the hashed Patricia Trie (Kniesburges and Scheideler WALCOM'11) that enables efficient prefix search on a set of keys. The data structure has a wide area of applications including string matching problems while offering low overhead and efficient operations when embedded on top of a distributed hash table. Especially, longest prefix matching for $x$ can be done in $\mathcal{O}(\log |x|)$ hash table read accesses. We show how to maintain the structure in a self-stabilizing way. Our protocol assures low overhead in a legal state and a total (asymptotically optimal) memory demand of $\Theta(d)$ bits, where $d$ is the number of bits needed for storing all keys. AU - Knollmann, Till AU - Scheideler, Christian ED - Izumi, Taisuke ED - Kuznetsov, Petr ID - 4411 KW - Self-Stabilizing KW - Prefix Search KW - Distributed Data Structure T2 - Proceedings of the 20th International Symposium on Stabilization, Safety, and Security of Distributed Systems (SSS) TI - A Self-Stabilizing Hashed Patricia Trie VL - 11201 ER - TY - CONF AB - Ultrasonic wire bonding is an indispensable process in the industrial manufacturing of semiconductor devices. Copper wire is increasingly replacing the well-established aluminium wire because of its superior electrical, thermal and mechanical properties. Copper wire processes differ significantly from aluminium processes and are more sensitive to disturbances, which reduces the range of parameter values suitable for a stable process. Disturbances can be compensated by an adaption of process parameters, but finding suitable parameters manually is difficult and time-consuming. This paper presents a physical model of the ultrasonic wire bonding process including the friction contact between tool and wire. This model yields novel insights into the process. A prototype of a multi-objective optimizing bonding machine (MOBM) is presented. It uses multi-objective optimization, based on the complete process model, to automatically select the best operating point as a compromise of concurrent objectives. AU - Unger, Andreas AU - Hunstig, Matthias AU - Meyer, Tobias AU - Brökelmann, Michael AU - Sextro, Walter ID - 9999 KW - wire bonding KW - multi-objective optimization KW - process model KW - copper wire KW - self-optimization T2 - In Proceedings of IMAPS 2018 – 51st Symposium on Microelectronics, Pasadena, CA, 2018 TI - Intelligent Production of Wire Bonds using Multi-Objective Optimization – Insights, Opportunities and Challenges VL - Vol. 2018, No. 1, pp. 000572-000577. ER - TY - JOUR AB - Sociogenesis addresses a pervasive problem in psychology given by Cartesian dualism that assigns the mental an inner locus apart from material activity. Aligning ourselves to the ongoing critical discussions of interiorization in psychology, we explore the crucial notion of space by highlighting language as sociocultural and dialogical activity performed by other-oriented individuals. We discuss space in terms of the “language spacetime”, a symbolic, embodied formation of mutually positioned speaking and listening selves. This leads beyond the “inside-outside” container metaphor and allows for a reformulation of interiorization. Interiorization is conceptualized as a continuous series of different, though mutually related movements between self and other and self and self that lead to and are supported by specific formations in language activity: reversion, transposition, and decoupling. Along a short passage of a video-based interview, we trace the reversion of dialogical positions within the addressivity constellation of the two interlocutors, their interactive creation of a heterotopic spacetime, and the decoupling of one speaker's psychological activity from the concrete here-and-now and the present other by moving and acting into this new sphere. Interiorization appears as a movement at the border of past, present, and possible future(s). AU - Bertau, Marie-Cécile AU - Karsten, Andrea ID - 32158 JF - New Ideas in Psychology KW - Interiorization KW - Dialogical self KW - Language activity KW - Voice KW - Vygotsky KW - Heterotopia KW - Video-confrontation SN - 0732-118X TI - Reconsidering interiorization: Self moving across language spacetimes VL - 49 ER - TY - THES AB - Reliability-adaptive systems allow an adaptation of system behavior based on current system reliability. They can extend their lifetime at the cost of lowered performance or vice versa. This can be used to adapt failure behavior according to a maintenance plan, thus increasing availability while using up system capability fully. To facilitate setup, a control algorithm independent of a degradation model is desired. A closed loop control technique for reliability based on a health index, a measure for system degradation, is introduced. It uses self-optimization as means to implement behavior adaptation. This is based on selecting the priorities of objectives that the system pursues. Possible working points are computed beforehand using model-based multiobjective optimization techniques. The controller selects the priorities of objectives and this way balances reliability and performance. As exemplary application, an automatically actuated single plate dry clutch is introduced. The entire reliability control is setup and lifetime experiments are conducted. Results show that the variance of time to failure is reduced greatly, making the failure behavior more predictable. At the same time, the desired usable lifetime can be extended at the cost of system performance to allow for changed maintenance intervals. Together, these possibilities allow for greater system usage and better planning of maintenance. AU - Meyer, Tobias ID - 9994 KW - dependability KW - reliability KW - behavior adaptation KW - self-optimization KW - multiobjective optimization KW - optimal control KW - automotive drivetrain KW - clutch system KW - reliability-adaptive system TI - Optimization-based reliability control of mechatronic systems ER - TY - JOUR AB - Research on entrepreneurial learning highlights the importance of experience and prior knowledge to entrepreneurial success. However, a conundrum remains and we are still seeking answers as to why some novice entrepreneurs learn successfully from their experiences and succeed, while some experienced entrepreneurs fail with their ventures. In order to advance the discussion about the role of experience during entrepreneurial learning, our critical reflection aims to (1) highlight some of the shortcomings of experiential learning theory (ELT) and (2) illustrate how alternative theoretical perspectives have the potential to advance our conceptual understanding of entrepreneurial learning processes. We argue for an explanation of entrepreneurial learning as a dynamic and self-regulated process that relies on planning, monitoring, and self-reflection. AU - Fust, Alexander Paul AU - Jenert, Tobias AU - Winkler, Christoph ID - 4419 IS - 2 JF - Entrepreneurship Research Journal KW - entrepreneurial learning KW - experiential learning KW - self-regulated learning TI - Experiential or Self-Regulated Learning: A Critical Reflection of Entrepreneurial Learning Processes VL - 8 ER - TY - CONF AB - Piezoelectric transducers are used in a wide range of applications. Reliability of these transducers is an important aspect in their application. Prognostics, which involve continuous monitoring of the health of technical systems and using this information to estimate the current health state and consequently predict the remaining useful lifetime (RUL), can be used to increase the reliability, safety, and availability of the transducers. This is achieved by utilizing the health state and RUL predictions to adaptively control the usage of the components or to schedule appropriate maintenance without interrupting operation. In this work, a prognostic approach utilizing self-sensing, where electric signals of a piezoelectric transducer are used as the condition monitoring data, is proposed. The approach involves training machine learning algorithms to model the degradation of the transducers through a health index and the use of the learned model to estimate the health index of similar transducers. The current health index is then used to estimate RUL of test components. The feasibility of the approach is demonstrated using piezoelectric bimorphs and the results show that the method is accurate in predicting the health index and RUL. AU - Kimotho, James Kuria AU - Sextro, Walter AU - Hemsel, Tobias ID - 9978 KW - Estimation of Remaining Useful Lifetime of Piezoelectric Transducers Based on Self-Sensing T2 - IEEE Transactions on Reliability TI - Estimation of Remaining Useful Lifetime of Piezoelectric Transducers Based on Self-Sensing ER - TY - CONF AU - Ho, Nam AU - Kaufmann, Paul AU - Platzner, Marco ID - 10676 KW - Linux KW - cache storage KW - microprocessor chips KW - multiprocessing systems KW - LEON3-Linux based multicore processor KW - MiBench suite KW - block sizes KW - cache adaptation KW - evolvable caches KW - memory-to-cache-index mapping function KW - processor caches KW - reconfigurable cache mapping optimization KW - reconfigurable hardware technology KW - replacement strategies KW - standard Linux OS KW - time a complete hardware implementation KW - Hardware KW - Indexes KW - Linux KW - Measurement KW - Multicore processing KW - Optimization KW - Training T2 - 2017 International Conference on Field Programmable Technology (ICFPT) TI - Evolvable caches: Optimization of reconfigurable cache mappings for a LEON3/Linux-based multi-core processor ER - TY - CONF AU - Guettatfi, Zakarya AU - Hübner, Philipp AU - Platzner, Marco AU - Rinner, Bernhard ID - 10780 KW - embedded systems KW - image sensors KW - power aware computing KW - wireless sensor networks KW - Zynq-based VSN node prototype KW - computational self-awareness KW - design approach KW - platform levels KW - power consumption KW - visual sensor networks KW - visual sensor nodes KW - Cameras KW - Hardware KW - Middleware KW - Multicore processing KW - Operating systems KW - Runtime KW - Reconfigurable platforms KW - distributed embedded systems KW - performance-resource trade-off KW - self-awareness KW - visual sensor nodes T2 - 12th International Symposium on Reconfigurable Communication-centric Systems-on-Chip (ReCoSoC) TI - Computational self-awareness as design approach for visual sensor nodes ER - TY - CONF AB - Websites increasingly embed semantic data for search engine optimization. The most common ontology for semantic data, schema.org, is supported by all major search engines and describes over 500 data types, including calendar events, recipes, products, and TV shows. As of today, users wishing to pass this data to their favorite applications, e.g., their calendars, cookbooks, price comparison applications or even smart devices such as TV receivers, rely on cumbersome and error-prone workarounds such as reentering the data or a series of copy and paste operations. In this paper, we present Semantic Data Mediator (SDM), an approach that allows the easy transfer of semantic data to a multitude of services, ranging from web services to applications installed on different devices. SDM extracts semantic data from the currently displayed web page on the client-side, offers suitable services to the user, and by the press of a button, forwards this data to the desired service while doing all the necessary data conversion and service interface adaptation in between. To realize this, we built a reusable repository of service descriptions, data converters, and service adapters, which can be extended by the crowd. Our approach for linking services to websites relies solely on semantic data and does not require any additional support by either website or service developers. We have fully implemented our approach and present a real-world case study demonstrating its feasibility and usefulness. AU - Wolters, Dennis AU - Heindorf, Stefan AU - Kirchhoff, Jonas AU - Engels, Gregor ED - Altintas, Ilkay ED - Chen, Shiping ID - 5829 KW - Services KW - Websites KW - Semantic Data KW - schema.org KW - Data Conversion KW - Interface Adaptation KW - Mediation SN - 9781538607527 T2 - 2017 IEEE International Conference on Web Services (ICWS) TI - Linking Services to Websites by Leveraging Semantic Data ER - TY - JOUR AB - Time-variant age information of different parts of a system can be used for system-level performance improvement through high-level task scheduling, thus extending the life-time of the system. Progressive age information should provide the age state that the system is in, and the rate that it is being aged at. In this paper, we propose a structure that monitors certain paths of a circuit and detects its gradual age growth, and provides the aging rate and aging state of the circuit. The proposed monitors are placed on a selected set of nodes that represent a timing bottleneck of the system. These monitors sample expected data on these nodes, and compare them with the expected values. The timing of sampling changes as the circuit ages and its delay increases. The timing of sampling will provide a measure of aging advancement of a circuit. To assess the efficacy of the proposed method and compare it with other state-of-the-art aging monitors, we use them on selected nodes of the execution unit of different processors, as well as some circuits from ITC99 benchmarks. The results reveal that the precision of our proposed method is between 0.12 (ns) to 0.401 (ns). Its Area and power overhead are negligible and are about 2.13 and 0.69 percent respectively. AU - Sadeghi-Kohan, Somayeh AU - Kamal, Mehdi AU - Navabi, Zainalabedin ID - 29462 IS - 3 JF - IEEE Transactions on Emerging Topics in Computing KW - Age advancement KW - age monitoring clock KW - aging rate KW - self-adjusting monitors SN - 2168-6750 TI - Self-Adjusting Monitor for Measuring Aging Rate and Advancement VL - 8 ER - TY - CONF AB - Usage of copper wire bonds allows to push power boundaries imposed by aluminum wire bonds. Copper allows higher electrical, thermal and mechanical loads than aluminum, which currently is the most commonly used material in heavy wire bonding. This is the main driving factor for increased usage of copper in high power applications such as wind turbines, locomotives or electric vehicles. At the same time, usage of copper also increases tool wear and reduces the range of parameter values for a stable process, making the process more challenging. To overcome these drawbacks, parameter adaptation at runtime using self-optimization is desired. A self-optimizing system is based on system objectives that evaluate and quantify system performance. System parameters can be changed at runtime such that pre-selected objective values are reached. For adaptation of bond process parameters, model-based self-optimization is employed. Since it is based on a model of the system, the bond process was modeled. In addition to static model parameters such as wire and substrate material properties and vibration characteristics of transducer and tool, variable model inputs are process parameters. Main simulation result is bonded area in the wiresubstrate contact. This model is then used to find valid and optimal working points before operation. The working point is composed of normal force and ultrasonic voltage trajectories, which are usually determined experimentally. Instead, multiobjective optimalization is used to compute trajectories that simultaneously optimize bond quality, process duration, tool wear and probability of tool-substrate contacts. The values of these objectives are computed using the process model. At runtime, selection among pre-determined optimal working points is sufficient to prioritize individual objectives. This way, the computationally expensive process of numerically solving a multiobjective optimal control problem and the demanding high speed bonding process are separated. To evaluate to what extent the pre-defined goals of self-optimization are met, an offthe- shelf heavy wire bonding machine was modified to allow for parameter adaptation and for transmitting of measurement data at runtime. This data is received by an external computer system and evaluated to select a new working point. Then, new process parameters are sent to the modified bonding machine for use for subsequent bonds. With these components, a full self-optimizing system has been implemented. AU - Meyer , Tobias AU - Unger, Andreas AU - Althoff, Simon AU - Sextro, Walter AU - Brökelmann, Michael AU - Hunstig, Matthias AU - Guth, Karsten ID - 9966 KW - Self-optimization KW - adaptive system KW - bond process KW - copper wire T2 - IEEE 66th Electronic Components and Technology Conference TI - Reliable Manufacturing of Heavy Copper Wire Bonds Using Online Parameter Adaptation ER - TY - JOUR AU - Torresen, Jim AU - Plessl, Christian AU - Yao, Xin ID - 1772 IS - 7 JF - IEEE Computer KW - self-awareness KW - self-expression TI - Self-Aware and Self-Expressive Systems – Guest Editor's Introduction VL - 48 ER - TY - JOUR AB - Advancements in information technology have changed the way customers experience a service encounter and their relationship with service providers. Especially technology-based self-service channels have found their way into the 21st century service economy. While research embraces these channels for their cost-efficiency, it has not examined whether a shift from personal to self-service affects customer–firm relationships. Drawing from the service-dominant logic and its central concept of value-in-context, we discuss customers’ value creation in self-service and personal service channels and examine the long-term impact of these channels on customer retention. Using longitudinal customer data, we investigate how the ratio of self-service versus personal service use influences customer defection over time. Our findings suggest that the ratio of self-service to personal service used affects customer defection in a U-shaped manner, with intermediate levels of both self-service and personal service use being associated with the lowest likelihood of defection. We also find that this effect mitigates over time. We conclude that firms should not shift customers toward self-service channels completely, especially not at the beginning of a relationship. Our study underlines the importance of understanding when and how self-service technologies create valuable customer experiences and stresses the notion of actively managing customers’ cocreation of value. AU - Scherer, Anne AU - Wünderlich, Nancy AU - Von Wangenheim, Florian ID - 5704 IS - 1 JF - MIS Quarterly KW - customer defection KW - customer retention KW - e-service KW - longitudinal KW - Self-service KW - value-in-context SN - 0276-7783. TI - The Value of Self-Service: Long-Term Effects of Technology-Based Self-Service Usage on Customer Retention. VL - 39 ER - TY - CONF AB - A highly selective first study phase in many Swiss study programs leads to a rather competitive climate among students. However, the atmosphere at the university is an important factor for students' transition into Higher Education. An important question in this context is whether students' are equipped with different dispositions influencing how they cope with this transition. Other research has already shown that different groups of students can be identified regarding their student behavior. Yet, so far little is known about patterns of variables characterizing students, transitioning successfully. The paper takes advantage of a person-centered approach, i.e. the latent-class analysis, which makes it possible to identify groups of individuals, sharing common attributes. The research was conducted as a longitudinal study during their first year at a Swiss university. The return rate was about 67%, with 820 utilizable questionnaires at t1. Based on the analysis of students' anxiety, intrinsic motivation and self-efficacy, three distinct classes of students could be identified. The first class can be called the "highly motivated and self-confident" students. The second class is characterized by the same pattern, however, on a more intermediate level and the last class can be described as the "least motivated and most anxious" group of students. This study contributes to research and theory on students' transition into higher education and could be a first hint that students' experiences of this transition can vary substantially. AU - Brahm, Taiga AU - Wagner, Dietrich AU - Jenert, Tobias ID - 4464 KW - Quantitative methods KW - Self-efficacy KW - Higher education KW - Motivation and Emotion TI - A person-centred approach to students' transition into Higher Education ER - TY - JOUR AB - Eine Vielzahl von Prozessen in der Chemie und Verfahrenstechnik kann durch Ultraschall positiv beeinflusst werden. Oftmals ist ultraschallinduzierte Kavitation der Hauptwirkmechanismus für die positiven Effekte der Beschallung. Daher ist es notwendig die Kavitationsaktivität während des Prozesses zu quantifizieren um die Beschallung für den jeweiligen Prozess optimal gestalten und überwachen zu können. Eine Möglichkeit der prozessbegleitenden Kavitationsdetektion ist die Auswertung der akustischen Emissionen von oszillierenden und kollabierenden Kavitationsblasen mittels Drucksensoren in der Flüssigkeit. Raue Prozessrandbedingungen wie hohe Temperaturen oder aggressive Flüssigkeiten erschweren es jedoch geeignete Sensoren zu finden. Als Alternative wurde daher die Nutzbarkeit der Rückwirkung von Kavitationsereignissen auf das elektrische Eingansgssignal des Ultraschallwandlers zur Quantifizierung von Kavitation untersucht. Die experimentelle Analyse hat ergeben, dass das Einsetzen und in einigen Fällen auch die Art der Kavitation auf Basis der Rückwirkung auf das Stromsignal des Ultraschallwandlers bestimmt werden kann. Die Stärke der Kavitation war hingegen nicht aus den Stromsignalen abzuleiten. AU - Bornmann, Peter AU - Hemsel, Tobias AU - Sextro, Walter AU - Memoli, Gianluca AU - Hodnett, Mark AU - Zeqiri, Bajram ID - 9944 IS - 2 JF - tm - Technisches Messen KW - Kavitationsdetektion KW - Self-Sensing KW - So- nochemie KW - Ultraschallwandler TI - Kavitationsdetektion mittels Self-Sensing-Ultraschallwandler VL - 82 ER - TY - CONF AB - Intelligent mechatronic systems other the possibility to adapt system behavior to current dependability. This can be used to assure reliability by controlling system behavior to reach a pre-defined lifetime. By using such closed loop control, the margin of error of useful lifetime of an individual system is lowered. It is also possible to change the pre-defined lifetime during operation, by adapting system behavior to derate component usage. When planning maintenance actions, the remaining useful lifetime of each individual system has to be taken into account. Usually, stochastic properties of a fleet of systems are analyzed to create maintenance plans. Among these, the main factor is the probability of an individual system to last until maintenance. If condition-based maintenance is used, this is updated for each individual system using available information about its current state. By lowering the margin of error of useful lifetime, which directly corresponds to the time until maintenance, extended maintenance periods are made possible. Also using reliability-adaptive operation, a reversal of degradation driven maintenance planning is possible where a maintenance plan is setup not only according to system properties, but mainly to requirements imposed by maintenance personnel or infrastructure. Each system then adapts its behavior accordingly and fails according to the maintenance plan, making better use of maintenance personnel and system capabilities at the same time. In this contribution, the potential of maintenance plan driven system behavior adaptation is shown. A model including adaptation process and maintenance actions is simulated over full system lifetime to assess the advantages gained. AU - Meyer, Tobias AU - Kaul, Thorben AU - Sextro, Walter ID - 9949 KW - Adaptive systems KW - Reliability analysis KW - Availability KW - Adaptive control KW - Maintenance KW - Self-optimizing systems KW - Self-optimizing control KW - Stochastic Petri-nets T2 - Proceedings of the 9th IFAC Symposium on Fault Detection, Supervision and Safety for Technical Processes TI - Advantages of reliability-adaptive system operation for maintenance planning ER - TY - CONF AB - The parametric Bayesian Feature Enhancement (BFE) and a datadriven Denoising Autoencoder (DA) both bring performance gains in severe single-channel speech recognition conditions. The first can be adjusted to different conditions by an appropriate parameter setting, while the latter needs to be trained on conditions similar to the ones expected at decoding time, making it vulnerable to a mismatch between training and test conditions. We use a DNN backend and study reverberant ASR under three types of mismatch conditions: different room reverberation times, different speaker to microphone distances and the difference between artificially reverberated data and the recordings in a reverberant environment. We show that for these mismatch conditions BFE can provide the targets for a DA. This unsupervised adaptation provides a performance gain over the direct use of BFE and even enables to compensate for the mismatch of real and simulated reverberant data. AU - Heymann, Jahn AU - Haeb-Umbach, Reinhold AU - Golik, P. AU - Schlueter, R. ID - 11813 KW - codecs KW - signal denoising KW - speech recognition KW - Bayesian feature enhancement KW - denoising autoencoder KW - reverberant ASR KW - single-channel speech recognition KW - speaker to microphone distances KW - unsupervised adaptation KW - Adaptation models KW - Noise reduction KW - Reverberation KW - Speech KW - Speech recognition KW - Training KW - deep neuronal networks KW - denoising autoencoder KW - feature enhancement KW - robust speech recognition T2 - Acoustics, Speech and Signal Processing (ICASSP), 2015 IEEE International Conference on TI - Unsupervised adaptation of a denoising autoencoder by Bayesian Feature Enhancement for reverberant asr under mismatch conditions ER - TY - CONF AB - Haushaltsgeräte aus der Klasse der "Weißen Ware" tragen mit etwa einem Drittel ($34,2%$ \citeBDEW2013) zum privaten Energieverbrauch bei. Diese Veröffentlichung präsentiert eine Struktur und die dafür notwendige optimale Betriebsstrategie für Weiße Ware in einer Umgebung mit Strompreisen, die wegen der Volatilität der Regenerativen Energien stark fluktuieren. Das vorgeschlagene Konzept nutzt dafür ein dezentrales Energiemanagementsystem, das über drei Hierarchieebenen verteilt ist: die Geräteebene, die Haushaltsebene und die Ortsnetzebene. Auf der Geräteebene nutzt dieses Konzept zusätzlich Betriebsflexibilitäten der Haushaltsgeräte aus. AU - Stille, Karl Stephan Christian AU - Böcker, Joachim AU - Bettentrup, Ralf AU - Kaiser, Ingo ID - 29973 KW - Energy management KW - hybrid energy storage system KW - self-optimization KW - multi-objective optimization KW - adaptive systems KW - pareto set KW - SFB614-D1 KW - SFB614-D2 KW - LEA-Publikation KW - Eigene T2 - ETG-Fachtagung "Von Smart Grids zu Smart Markets" TI - Hierarchisches Optimierungskonzept für die Laststeuerung von Haushaltsgeräten ER - TY - CONF AU - King, Thomas C. AU - Liu, Qingzhi AU - Polevoy, Gleb AU - de Weerdt, Mathijs AU - Dignum, Virginia AU - van Riemsdijk, M. Birna AU - Warnier, Martijn ID - 17661 KW - crowd-sensing KW - crowdsourcing KW - data aggregation KW - game theory KW - norms KW - reciprocation KW - self interested agents KW - simulation SN - 978-1-4503-2738-1 T2 - Proceedings of the 2014 International Conference on Autonomous Agents and Multi-agent Systems TI - Request Driven Social Sensing ER - TY - CONF AB - Application of prognostics and health management (PHM) in the field of Proton Exchange Membrane (PEM) fuel cells is emerging as an important tool in increasing the reliability and availability of these systems. Though a lot of work is currently being conducted to develop PHM systems for fuel cells, various challenges have been encountered including the self-healing effect after characterization as well as accelerated degradation due to dynamic loading, all which make RUL predictions a difficult task. In this study, a prognostic approach based on adaptive particle filter algorithm is proposed. The novelty of the proposed method lies in the introduction of a self-healing factor after each characterization and the adaption of the degradation model parameters to fit to the changing degradation trend. An ensemble of five different state models based on weighted mean is then developed. The results show that the method is effective in estimating the remaining useful life of PEM fuel cells, with majority of the predictions falling within 5\% error. The method was employed in the IEEE 2014 PHM Data Challenge and led to our team emerging the winner of the RUL category of the challenge. AU - Kimotho, James Kuria AU - Meyer, Tobias AU - Sextro, Walter ID - 9879 KW - ageing KW - particle filtering (numerical methods) KW - proton exchange membrane fuel cells KW - remaining life assessment KW - PEM fuel cell prognostics KW - PHM KW - RUL predictions KW - accelerated degradation KW - adaptive particle filter algorithm KW - dynamic loading KW - model parameter adaptation KW - prognostics and health management KW - proton exchange membrane fuel cells KW - remaining useful life estimation KW - self-healing effect KW - Adaptation models KW - Data models KW - Degradation KW - Estimation KW - Fuel cells KW - Mathematical model KW - Prognostics and health management T2 - Prognostics and Health Management (PHM), 2014 IEEE Conference on TI - PEM fuel cell prognostics using particle filter with model parameter adaptation ER - TY - CONF AB - So-called reliability adaptive systems are able to adapt their system behavior based on the current reliability of the system. This allows them to react to changed operating conditions or faults within the system that change the degradation behavior. To implement such reliability adaptation, self-optimization can be used. A self-optimizing system pursues objectives, of which the priorities can be changed at runtime, in turn changing the system behavior. When including system reliability as an objective of the system, it becomes possible to change the system based on the current reliability as well. This capability can be used to control the reliability of the system throughout its operation period in order to achieve a pre-defined or user-selectable system lifetime. This way, optimal planning of maintenance intervals is possible while also using the system capabilities to their full extent. Our proposed control system makes it possible to react to changed degradation behavior by selecting objectives of the self-optimizing system and in turn changing the operating parameters in a closed loop. A two-stage controller is designed which is used to select the currently required priorities of the objectives in order to fulfill the desired usable lifetime. Investigations using a model of an automotive clutch system serve to demonstrate the feasibility of our controller. It is shown that the desired lifetime can be achieved reliably. AU - Meyer , Tobias AU - Sextro, Walter ID - 9884 KW - self-optimization reliability adaptive T2 - Proceedings of the Second European Conference of the Prognostics and Health Management Society 2014 TI - Closed-loop Control System for the Reliability of Intelligent Mechatronic Systems VL - 5 ER - TY - JOUR AB - Intelligent mechatronic systems, such as self-optimizing systems, allow an adaptation of the system behavior at runtime based on the current situation. To do so, they generally select among several pre-defined working points. A common method to determine working points for a mechatronic system is to use model-based multiobjective optimization. It allows finding compromises among conflicting objectives, called objective functions, by adapting parameters. To evaluate the system behavior for different parameter sets, a model of the system behavior is included in the objective functions and is evaluated during each function call. Intelligent mechatronic systems also have the ability to adapt their behavior based on their current reliability, thus increasing their availability, or on changed safety requirements; all of which are summed up by the common term dependability. To allow this adaptation, dependability can be considered in multiobjective optimization by including dependability-related objective functions. However, whereas performance-related objective functions are easily found, formulation of dependability-related objective functions is highly system-specific and not intuitive, making it complex and error-prone. Since each mechatronic system is different, individual failure modes have to be taken into account, which need to be found using common methods such as Failure-Modes and Effects Analysis or Fault Tree Analysis. Using component degradation models, which again are specific to the system at hand, the main loading factors can be determined. By including these in the model of the system behavior, the relation between working point and dependability can be formulated as an objective function. In our work, this approach is presented in more detail. It is exemplified using an actively actuated single plate dry clutch system. Results show that this approach is suitable for formulating dependability-related objective functions and that these can be used to extend system lifetime by adapting system behavior. AU - Meyer , Tobias AU - Sondermann-Wölke, Christoph AU - Sextro, Walter ID - 9885 JF - Conference Proceedings of the 2nd International Conference on System-Integrated Intelligence KW - Self-optimization KW - multiobjective optimization KW - objective function KW - dependability KW - intelligent system KW - behavior adaptation TI - Method to Identify Dependability Objectives in Multiobjective Optimization Problem VL - 15 ER - TY - CONF AU - Ho, Nam AU - Kaufmann, Paul AU - Platzner, Marco ID - 10677 KW - Linux KW - cache storage KW - embedded systems KW - granular computing KW - multiprocessing systems KW - reconfigurable architectures KW - Leon3 SPARe processor KW - custom logic events KW - evolvable-self-adaptable processor cache KW - fine granular profiling KW - integer unit events KW - measurement infrastructure KW - microarchitectural events KW - multicore embedded system KW - perf_event standard Linux performance measurement interface KW - processor properties KW - run-time reconfigurable memory-to-cache address mapping engine KW - run-time reconfigurable multicore infrastructure KW - split-level caching KW - Field programmable gate arrays KW - Frequency locked loops KW - Irrigation KW - Phasor measurement units KW - Registers KW - Weaving T2 - 2014 {IEEE} Intl. Conf. on Evolvable Systems (ICES) TI - Towards self-adaptive caches: A run-time reconfigurable multi-core infrastructure ER -