@inproceedings{23465, abstract = {{One of the main objectives of production engineering is to reproducibly manufacture (complex) defect-free parts. To achieve this, it is necessary to employ an appropriate process or tool design. While this will generally prove successful, it cannot, however, offset stochastic defects with local variations in material properties. Closed-loop process control represents a promising approach for a solution in this context. The state of the art involves using this approach to control geometric parameters such as a length. So far, no research or applications have been conducted with closed-loop control for microstructure and product properties. In the project on which this paper is based, the local martensite content of parts is to be adjusted in a highly precise and reproducible manner. The forming process employed is a special, property-controlled flow-forming process. A model-based controller is thus to generate corresponding correction values for the tool-path geometry and tool-path velocity on the basis of online martensite content measurements. For the controller model, it is planned to use a special process or microstructure (correlation) model. The planned paper not only describes the experimental setup but also presents results of initial experimental investigations for subsequent use in the closed-loop control of α’-martensite content during flow-forming.}}, author = {{Arian, Bahman and Homberg, Werner and Riepold, Markus and Trächtler, Ansgar and Rozo Vasquez, Julian and Walther, Frank}}, isbn = {{978-2-87019-302-0}}, keywords = {{Flow-forming, Spinning, Process Strategy, Martensite Content, Property Control, Micromagnetic Measurement, Metastable Austenitic Stainless Steel}}, location = {{Liège, Belgium}}, publisher = {{ULiège Library}}, title = {{{Forming of metastable austenitic stainless steel tubes with axially graded martensite content by flow-forming}}}, year = {{2021}}, } @article{34484, abstract = {{Multiprofessionelle Teams sind notwendiger Bestandteil inklusiver Schulen. Die Verteilung von Aufgaben, welche über die Zusammenarbeit von allgemeinen und sonderpädagogi­schen Lehrkräften im Unterricht hinausgehen, wurde bislang jedoch selten systematisch untersucht. Im Beitrag werden deskriptive Befunde aus dem Projekt BiFoKi (Bielefelder Fortbildungskonzept zur Kooperation in inklusiven Schulen) zu den Zuständigkeiten von allgemeinen (N = 170) und sonderpädagogischen Lehrkräften (N = 24) sowie Schulsozial­arbeiterinnen (N = 11) an inklusiven Sekundar-­ und Gesamtschulen präsentiert. Sie deuten auf eine Persistenz traditioneller Rollenmuster und Aufgabenverteilungen hin. Bei den befragten sonderpädagogischen Lehrkräften können zwei unterschiedliche Rollenmuster herausgearbeitet werden. Die Schulsozialarbeiterinnen weisen ein enges Arbeitsfeld mit einem Fokus auf Eltern­-Schule-­Kooperation auf. }}, author = {{Neumann, Phillip and Grüter, Sandra and Eckel, Lisa and Lütje-Klose, Birgit and Wild, Elke and Gorges, Julia}}, issn = {{0513-9066}}, journal = {{Zeitschrift für Heilpädagogik}}, keywords = {{Inklusion, Sonderpädagogik, Sekundarstufe, Gesamtschulen, Kooperation, Schulsozialarbeit, BiFoKi}}, number = {{4}}, pages = {{164--177}}, title = {{{Aufgaben und Zuständigkeiten von allgemeinen und sonderpädagogischen Lehrkräften sowie Fachkräften der ­Schulsozialarbeit­ in­ inklusiven­ Schulen­ der­ Sekundarstufe I. Erste Ergebnisse aus dem BiFoKi-Projekt}}}, volume = {{73}}, year = {{2021}}, } @inproceedings{24080, abstract = {{Challenges of the development of mechatronic systems and corresponding production systems have increased steadily. Changes are primarily due to increased product complexity and the connection to the internet of things and services, enabling Cyber-Physical Systems (CPS) and Cyber-Physical Production Systems (CPPS). Major innovations of the revised VDI guideline 2206 for developing mechatronic systems are systems thinking as a core element and six checkpoints for structuring deliverables along the V-Model. These checkpoints serve for orientation in result progress and thus enable a structured and complete development process. However, tasks and checkpoints of the new guideline focus on the product development itself without integrating the development of related CPPS, enabling optimization simultaneously to system development. Implications are derived by a three-step analysis. The paper at hand contributes fundamental extensions of the checkpoint questions regarding integrated CPPS development. These questions provide methodical support for system developers of CPPS for CPS by enabling the project manager to check the status, schedule further development steps and evaluate the maturity of the whole, integrated development.}}, author = {{Gräßler, Iris and Wiechel, Dominik and Roesmann, Daniel and Thiele, Henrik}}, booktitle = {{Procedia CIRP}}, issn = {{2212-8271}}, keywords = {{Cyber-Physical Production System (CPPS), V-Model, Product System Development, Integrated Development, VDI 2206}}, pages = {{253--258}}, title = {{{V-model based development of cyber-physical systems and cyber-physical production systems}}}, doi = {{10.1016/j.procir.2021.05.119}}, year = {{2021}}, } @inproceedings{20681, abstract = {{The battle of developing hardware Trojans and corresponding countermeasures has taken adversaries towards ingenious ways of compromising hardware designs by circumventing even advanced testing and verification methods. Besides conventional methods of inserting Trojans into a design by a malicious entity, the design flow for field-programmable gate arrays (FPGAs) can also be surreptitiously compromised to assist the attacker to perform a successful malfunctioning or information leakage attack. The advanced stealthy malicious look-up-table (LUT) attack activates a Trojan only when generating the FPGA bitstream and can thus not be detected by register transfer and gate level testing and verification. However, also this attack was recently revealed by a bitstream-level proof-carrying hardware (PCH) approach. In this paper, we present a novel attack that leverages malicious routing of the inserted Trojan circuit to acquire a dormant state even in the generated and transmitted bitstream. The Trojan's payload is connected to primary inputs/outputs of the FPGA via a programmable interconnect point (PIP). The Trojan is detached from inputs/outputs during place-and-route and re-connected only when the FPGA is being programmed, thus activating the Trojan circuit without any need for a trigger logic. Since the Trojan is injected in a post-synthesis step and remains unconnected in the bitstream, the presented attack can currently neither be prevented by conventional testing and verification methods nor by recent bitstream-level verification techniques.}}, author = {{Ahmed, Qazi Arbab and Wiersema, Tobias and Platzner, Marco}}, booktitle = {{2021 Design, Automation & Test in Europe Conference & Exhibition (DATE)}}, location = {{Alpexpo | Grenoble, France}}, publisher = {{2021 Design, Automation and Test in Europe Conference (DATE)}}, title = {{{Malicious Routing: Circumventing Bitstream-level Verification for FPGAs}}}, doi = {{10.23919/DATE51398.2021.9474026}}, year = {{2021}}, } @article{29815, abstract = {{Aluminium steel clad materials have high potential for industrial applications. Their mechanical properties are governed by an intermetallic layer, which forms upon heat treatment at the Al-Fe interface. Transmission electron microscopy was employed to identify the phases present at the interface by selective area electron diffraction and energy dispersive spectroscopy. Three phases were identified: orthorhombic Al5Fe2, monoclinic Al13Fe4 and cubic Al19Fe4MnSi2. An effective interdiffusion coefficient dependent on concentration was determined according to the Boltzmann–Matano method. The highest value of the interdiffusion coefficient was reached at the composition of the intermetallic phases. Afterwards, the process of diffusion considering the evaluated interdiffusion coefficient was simulated using the finite element method. Results of the simulations revealed that growth of the intermetallic phases proceeds preferentially in the direction of aluminium.}}, author = {{Křivská, Barbora and Šlapáková, Michaela and Veselý, Jozef and Kihoulou, Martin and Fekete, Klaudia and Minárik, Peter and Králík, Rostislav and Grydin, Olexandr and Stolbchenko, Mykhailo and Schaper, Mirko}}, issn = {{1996-1944}}, journal = {{Materials}}, keywords = {{General Materials Science}}, number = {{24}}, publisher = {{MDPI AG}}, title = {{{Intermetallic Phases Identification and Diffusion Simulation in Twin-Roll Cast Al-Fe Clad Sheet}}}, doi = {{10.3390/ma14247771}}, volume = {{14}}, year = {{2021}}, } @article{24566, author = {{Engelkemeier, Katja and Sun, Aijia and Voswinkel, Dietrich and Grydin, Olexandr and Schaper, Mirko and Bremser, Wolfgang}}, issn = {{2196-0216}}, journal = {{ChemElectroChem}}, pages = {{2155--2168}}, publisher = {{Wiley}}, title = {{{Zinc Anodizing: Structural Diversity of Anodic Zinc Oxide Controlled by the Type of Electrolyte}}}, doi = {{10.1002/celc.202100216}}, year = {{2021}}, } @article{23803, author = {{Reitz, Alexander and Grydin, Olexandr and Schaper, Mirko}}, journal = {{Materials Data for Smart Forming Technologies}}, location = {{Freiberg}}, title = {{{Characterization of phase transformations during graded thermo- mechanical treatment of steel 22MnB5 by means of optical methods }}}, year = {{2021}}, } @article{21545, author = {{Masendorf, Lukas and Wächter, Michael and Esderts, Alfons and Otroshi, Mortaza and Meschut, Gerson}}, issn = {{8756-758X}}, journal = {{Fatigue & Fracture of Engineering Materials & Structures}}, pages = {{15}}, title = {{{Service life estimation of self‐piercing riveted joints by linear damage accumulation}}}, doi = {{10.1111/ffe.13446}}, year = {{2021}}, } @inproceedings{36527, author = {{Jensen, Solveig and Gasteiger, Hedwig and Bruns, Julia}}, booktitle = {{Proceedings of the 44th Conference of the International Group for the Psychology of Mathematics Education}}, editor = {{Inprasitha, Maitree and Changsri, Narumon and Boonsena, Nisakorn}}, location = {{Khon Kaen, Thailand}}, pages = {{101--109}}, title = {{{Place value and regrouping as seperate constructs of place value understanding}}}, volume = {{3}}, year = {{2021}}, } @inproceedings{36536, author = {{Jensen, Solveig and Gasteiger, Hedwig and Bruns, Julia}}, booktitle = {{Beiträge zum Mathematikunterricht 2021}}, location = {{Lüneburg}}, publisher = {{WTM-Verlag}}, title = {{{Stellenwertverständnis: Verständnis von Stellenwertprinzip und Bündelungsprinzip als separate Konstrukte}}}, doi = {{http://dx.doi.org/10.17877/DE290R-22292}}, year = {{2021}}, }