@article{58133,
  author       = {{Pramanik, Sudipta and Mileaege, Dennis and Andreiev, Anatolii and Hoyer, Kay-Peter and Schaper, Mirko}},
  issn         = {{1059-9495}},
  journal      = {{Journal of Materials Engineering and Performance}},
  publisher    = {{Springer Science and Business Media LLC}},
  title        = {{{Effect of Compression Rate and Pore Size Distribution on the Compression Behavior of Additively Manufactured Bio-inspired Fe3Si Microporous Material}}},
  doi          = {{10.1007/s11665-024-10618-z}},
  year         = {{2025}},
}

@article{41492,
  abstract     = {{<jats:p>The current investigation shows the feasibility of 316L steel powder production via three different argon gas atomisation routes (closed coupled atomisation, free fall atomisation with and without hot gas), along with subsequent sample production by laser powder bed fusion (PBF-LB). Here, a mixture of pure Fe and atomised 316L steel powder is used for PBF-LB to induce a chemical composition gradient in the microstructure. Optical microscopy and μ-CT investigations proved that the samples processed by PBF-LB exhibit very little porosity. Combined EBSD-EDS measurements show the chemical composition gradient leading to the formation of a local fcc-structure. Upon heat treatment (1100 °C, 14 h), the chemical composition is homogeneous throughout the microstructure. A moderate decrease (1060 to 985 MPa) in the sample’s ultimate tensile strength (UTS) is observed after heat treatment. However, the total elongation of the as-built and heat-treated samples remains the same (≈22%). Similarly, a slight decrease in the hardness from 341 to 307 HV1 is observed upon heat treatment.</jats:p>}},
  author       = {{Pramanik, Sudipta and Andreiev, Anatolii and Hoyer, Kay-Peter and Krüger, Jan Tobias and Hengsbach, Florian and Kircheis, Alexander and Zhao, Weiyu and Fischer-Bühner, Jörg and Schaper, Mirko}},
  issn         = {{2674-0516}},
  journal      = {{Powders}},
  number       = {{1}},
  pages        = {{59--74}},
  publisher    = {{MDPI AG}},
  title        = {{{Powder Production via Atomisation and Subsequent Laser Powder Bed Fusion Processing of Fe+316L Steel Hybrid Alloy}}},
  doi          = {{10.3390/powders2010005}},
  volume       = {{2}},
  year         = {{2023}},
}

@article{44078,
  author       = {{Andreiev, Anatolii and Hoyer, Kay-Peter and Hengsbach, Florian and Haase, Michael and Tasche, Lennart and Duschik, Kristina and Schaper, Mirko}},
  issn         = {{0924-0136}},
  journal      = {{Journal of Materials Processing Technology}},
  keywords     = {{Industrial and Manufacturing Engineering, Metals and Alloys, Computer Science Applications, Modeling and Simulation, Ceramics and Composites}},
  publisher    = {{Elsevier BV}},
  title        = {{{Powder bed fusion of soft-magnetic iron-based alloys with high silicon content}}},
  doi          = {{10.1016/j.jmatprotec.2023.117991}},
  volume       = {{317}},
  year         = {{2023}},
}

@article{46507,
  author       = {{Pramanik, Sudipta and Milaege, Dennis and Hein, Maxwell and Andreiev, Anatolii and Schaper, Mirko and Hoyer, Kay-Peter}},
  issn         = {{1438-1656}},
  journal      = {{Advanced Engineering Materials}},
  keywords     = {{Condensed Matter Physics, General Materials Science}},
  number       = {{14}},
  publisher    = {{Wiley}},
  title        = {{{An Experimental and Computational Modeling Study on Additively Manufactured Micro‐Architectured Ti–24Nb–4Zr–8Sn Hollow‐Strut Lattice Structures}}},
  doi          = {{10.1002/adem.202201850}},
  volume       = {{25}},
  year         = {{2023}},
}

@article{33498,
  author       = {{Krüger, Jan Tobias and Hoyer, Kay-Peter and Andreiev, Anatolii and Schaper, Mirko and Zinn, Carolin}},
  journal      = {{Advanced Engineering Materials}},
  title        = {{{Modification of Iron with Degradable Silver Phases Processed via Laser Beam Melting for Implants with Adapted Degradation Rate}}},
  doi          = {{https://doi.org/10.1002/adem.202201008}},
  year         = {{2022}},
}

@article{41493,
  author       = {{Krüger, Jan Tobias and Hoyer, Kay-Peter and Andreiev, Anatolii and Schaper, Mirko and Zinn, Carolin}},
  issn         = {{1438-1656}},
  journal      = {{Advanced Engineering Materials}},
  keywords     = {{Condensed Matter Physics, General Materials Science}},
  publisher    = {{Wiley}},
  title        = {{{Modification of Iron with Degradable Silver Phases Processed via Laser Beam Melting for Implants with Adapted Degradation Rate}}},
  doi          = {{10.1002/adem.202201008}},
  year         = {{2022}},
}

@article{24535,
  abstract     = {{<jats:p>Implementing the concept of mixed construction in modern automotive engineering requires the joining of sheet metal or extruded profiles with cast components made from different materials. As weight reduction is desired, these cast components are usually made from high-strength aluminium alloys of the Al-Si (Mn, Mg) system, which have limited weldability. The mechanical joinability of the cast components depends on their ductility, which is influenced by the microstructure. High-strength cast aluminium alloys have relatively low ductility, which leads to cracking of the joints. This limits the range of applications for cast aluminium alloys. In this study, an aluminium alloy of the Al-Si system AlSi9 is used to investigate relationships between solidification conditions during the sand casting process, microstructure, mechanical properties, and joinability. The demonstrator is a stepped plate with a minimum thickness of 2.0 mm and a maximum thickness of 4.0 mm, whereas the thickness difference between neighbour steps amounts to 0.5 mm. During casting trials, the solidification rates for different plate steps were measured. The microscopic investigations reveal a correlation between solidification rates and microstructure parameters such as secondary dendrite arm spacing. Furthermore, mechanical properties and the mechanical joinability are investigated.</jats:p>}},
  author       = {{Neuser, Moritz and Grydin, Olexandr and Andreiev, Anatolii and Schaper, Mirko}},
  issn         = {{2075-4701}},
  journal      = {{Metals}},
  title        = {{{Effect of Solidification Rates at Sand Casting on the Mechanical Joinability of a Cast Aluminium Alloy}}},
  doi          = {{10.3390/met11081304}},
  year         = {{2021}},
}

@article{41512,
  author       = {{Andreiev, Anatolii and Hoyer, Kay-Peter and Dula, Dimitri and Hengsbach, Florian and Grydin, Olexandr and Frolov, Yaroslav and Schaper, Mirko}},
  issn         = {{0921-5093}},
  journal      = {{Materials Science and Engineering: A}},
  keywords     = {{Mechanical Engineering, Mechanics of Materials, Condensed Matter Physics, General Materials Science}},
  publisher    = {{Elsevier BV}},
  title        = {{{Laser beam melting of functionally graded materials with application-adapted tailoring of magnetic and mechanical performance}}},
  doi          = {{10.1016/j.msea.2021.141662}},
  volume       = {{822}},
  year         = {{2021}},
}

@article{41510,
  author       = {{Pramanik, Sudipta and Andreiev, Anatolii and Hoyer, Kay-Peter and Schaper, Mirko}},
  issn         = {{0142-1123}},
  journal      = {{International Journal of Fatigue}},
  keywords     = {{Industrial and Manufacturing Engineering, Mechanical Engineering, Mechanics of Materials, General Materials Science, Modeling and Simulation}},
  publisher    = {{Elsevier BV}},
  title        = {{{Quasi in-situ analysis of fracture path during cyclic loading of double-edged U notched additively manufactured FeCo alloy}}},
  doi          = {{10.1016/j.ijfatigue.2021.106498}},
  volume       = {{153}},
  year         = {{2021}},
}

@article{23913,
  abstract     = {{<jats:p>Implementing the concept of mixed construction in modern automotive engineering requires the joining of sheet metal or extruded profiles with cast components made from different materials. As weight reduction is desired, these cast components are usually made from high-strength aluminium alloys of the Al-Si (Mn, Mg) system, which have limited weldability. The mechanical joinability of the cast components depends on their ductility, which is influenced by the microstructure. High-strength cast aluminium alloys have relatively low ductility, which leads to cracking of the joints. This limits the range of applications for cast aluminium alloys. In this study, an aluminium alloy of the Al-Si system AlSi9 is used to investigate relationships between solidification conditions during the sand casting process, microstructure, mechanical properties, and joinability. The demonstrator is a stepped plate with a minimum thickness of 2.0 mm and a maximum thickness of 4.0 mm, whereas the thickness difference between neighbour steps amounts to 0.5 mm. During casting trials, the solidification rates for different plate steps were measured. The microscopic investigations reveal a correlation between solidification rates and microstructure parameters such as secondary dendrite arm spacing. Furthermore, mechanical properties and the mechanical joinability are investigated.</jats:p>}},
  author       = {{Neuser, Moritz and Grydin, Olexandr and Andreiev, Anatolii and Schaper, Mirko}},
  issn         = {{2075-4701}},
  journal      = {{Metals}},
  title        = {{{Effect of Solidification Rates at Sand Casting on the Mechanical Joinability of a Cast Aluminium Alloy}}},
  doi          = {{10.3390/met11081304}},
  year         = {{2021}},
}

@article{23897,
  author       = {{Andreiev, Anatolii and Hoyer, Kay-Peter and Dula, Dimitri and Hengsbach, Florian and Grydin, Olexandr and Frolov, Yaroslav and Schaper, Mirko}},
  issn         = {{0921-5093}},
  journal      = {{Materials Science and Engineering: A}},
  title        = {{{Laser beam melting of functionally graded materials with application-adapted tailoring of magnetic and mechanical performance}}},
  doi          = {{10.1016/j.msea.2021.141662}},
  year         = {{2021}},
}

@article{23911,
  author       = {{Pramanik, Sudipta and Andreiev, Anatolii and Hoyer, Kay-Peter and Schaper, Mirko}},
  issn         = {{0142-1123}},
  journal      = {{International Journal of Fatigue}},
  title        = {{{Quasi in-situ analysis of fracture path during cyclic loading of double-edged U notched additively manufactured FeCo alloy}}},
  doi          = {{10.1016/j.ijfatigue.2021.106498}},
  year         = {{2021}},
}

@article{41508,
  author       = {{Camberg, Alan Adam and Andreiev, Anatolii and Pramanik, Sudipta and Hoyer, Kay-Peter and Tröster, Thomas and Schaper, Mirko}},
  issn         = {{0921-5093}},
  journal      = {{Materials Science and Engineering: A}},
  keywords     = {{Mechanical Engineering, Mechanics of Materials, Condensed Matter Physics, General Materials Science}},
  publisher    = {{Elsevier BV}},
  title        = {{{Strength enhancement of AlMg sheet metal parts by rapid heating and subsequent cold die stamping of severely cold-rolled blanks}}},
  doi          = {{10.1016/j.msea.2021.142312}},
  volume       = {{831}},
  year         = {{2021}},
}

@article{27700,
  author       = {{Camberg, Alan Adam and Andreiev, Anatolii and Pramanik, Sudipta and Hoyer, Kay-Peter and Tröster, Thomas and Schaper, Mirko}},
  issn         = {{0921-5093}},
  journal      = {{Materials Science and Engineering: A}},
  publisher    = {{Elsevier}},
  title        = {{{Strength enhancement of AlMg sheet metal parts by rapid heating and subsequent cold die stamping of severely cold-rolled blanks}}},
  doi          = {{10.1016/j.msea.2021.142312}},
  year         = {{2021}},
}

@article{23898,
  author       = {{Andreiev, Anatolii and Hoyer, Kay-Peter and Dula, Dimitri and Hengsbach, Florian and Haase, Michael and Gierse, Jan and Zimmer, Detmar and Tröster, Thomas and Schaper, Mirko}},
  issn         = {{0924-0136}},
  journal      = {{Journal of Materials Processing Technology}},
  title        = {{{Soft-magnetic behavior of laser beam melted FeSi3 alloy with graded cross-section}}},
  doi          = {{10.1016/j.jmatprotec.2021.117183}},
  year         = {{2021}},
}

@phdthesis{42012,
  author       = {{Andreiev, Anatolii}},
  isbn         = {{9783751900089}},
  publisher    = {{Books on Demand}},
  title        = {{{Kurzzeitaustenitisierung höchstfester Stähle – eine zeiteffiziente Methode zur Fertigung sicherheitsrelevanter Bauteile mit verbesserten Eigenschaften}}},
  year         = {{2020}},
}

@article{41522,
  author       = {{Andreiev, Anatolii and Hoyer, Kay-Peter and Grydin, Olexandr and Frolov, Yaroslav and Schaper, Mirko}},
  issn         = {{0933-5137}},
  journal      = {{Materialwissenschaft und Werkstofftechnik}},
  keywords     = {{Mechanical Engineering, Mechanics of Materials, Condensed Matter Physics, General Materials Science}},
  number       = {{4}},
  pages        = {{517--530}},
  publisher    = {{Wiley}},
  title        = {{{Degradable silver‐based alloys}}},
  doi          = {{10.1002/mawe.201900191}},
  volume       = {{51}},
  year         = {{2020}},
}

@article{23899,
  author       = {{Grydin, Olexandr and Matzelt, Manuel and Andreiev, Anatolii and Frolov, Yaroslav and Schaper, Mirko}},
  issn         = {{1438-1656}},
  journal      = {{Advanced Engineering Materials}},
  title        = {{{Influence of Microstructure in Near‐Surface Areas of Feedstocks on the Bond Strength of Roll Bonded Aluminum Clads}}},
  doi          = {{10.1002/adem.202000130}},
  year         = {{2020}},
}

@article{23896,
  author       = {{Andreiev, Anatolii and Hoyer, Kay-Peter and Grydin, Olexandr and Frolov, Yaroslaw and Schaper, Mirko}},
  issn         = {{0933-5137}},
  journal      = {{Materialwissenschaft und Werkstofftechnik}},
  pages        = {{517--530}},
  title        = {{{Degradable silver‐based alloys}}},
  doi          = {{10.1002/mawe.201900191}},
  year         = {{2020}},
}

@article{23907,
  abstract     = {{<jats:p>One of the strategies employed to lower weight and to decrease material consumption is reducing part thickness itself. Thus, functionally graded materials in which structural reinforcement is adjusted locally, are of great interest. With regard to conventional industrial processes, such as extrusion or flexible cold rolling, thickness variations can only be achieved either longitudinally or through the cross-section of the semi-finished products. Hence, a combined thickness variation (along both axes) is difficult to generate solely by extrusion or rolling. A simultaneous thickness variation in both directions, however, would enable further weight savings in structural components such as car body parts. In this study, a promising approach with extruded shapes, serving as a billet for a flexible hot rolling process, is elaborated upon. By employing the described process modification, shapes with simultaneous thickness variations in longitudinal as well as in transverse direction are feasible. Initial numerical analysis reveals the weight-saving potential of using these semi-finished products for structural parts in a car body. A demonstration of the production process for the semi-finished parts and the occurring challenges are discussed. To verify and adjust the new technology, a numerical model of the flexible hot rolling process has been created based on the finite element software QForm VX. This model is also employed for tool design optimization to produce semi-finished components with the required geometrical quality. Finally, the results of hot rolling experiments conducted using the adjusted roll design are presented.</jats:p>}},
  author       = {{Grydin, Olexandr and Sotirov, Nikolay and Samsonenko, Andrii and Biba, Nikolay and Andreiev, Anatolii and Stolbchenko, Mykhailo and Behr, Teresa and Frolov, Iaroslav and Schaper, Mirko}},
  issn         = {{1662-9752}},
  journal      = {{Materials Science Forum}},
  pages        = {{85--92}},
  title        = {{{Flexible Hot Rolling of Extruded Shapes of Aluminum Alloy EN AW-6082}}},
  doi          = {{10.4028/www.scientific.net/msf.949.85}},
  year         = {{2019}},
}