@inproceedings{30498,
  author       = {{Henke, Christian and Trächtler, Ansgar}},
  booktitle    = {{2013 International Conference on Connected Vehicles and Expo (ICCVE)}},
  publisher    = {{IEEE}},
  title        = {{{Autonomously driven railway cabin convoys — Communication, control design and experimentation}}},
  doi          = {{10.1109/iccve.2013.6799806}},
  year         = {{2014}},
}

@inproceedings{30569,
  author       = {{Peters, Wilhelm and Böcker, Joachim}},
  booktitle    = {{IECON 2013 - 39th Annual Conference of the IEEE Industrial Electronics Society}},
  publisher    = {{IEEE}},
  title        = {{{Discrete-time design of adaptive current controller for interior permanent magnet synchronous motors (IPMSM) with high magnetic saturation}}},
  doi          = {{10.1109/iecon.2013.6700225}},
  year         = {{2014}},
}

@inproceedings{30568,
  author       = {{Buchholz, Oleg and Böcker, Joachim}},
  booktitle    = {{IECON 2013 - 39th Annual Conference of the IEEE Industrial Electronics Society}},
  publisher    = {{IEEE}},
  title        = {{{FPGA-based dynamically reconfigurable control of induction motor drives}}},
  doi          = {{10.1109/iecon.2013.6699698}},
  year         = {{2014}},
}

@inproceedings{30579,
  author       = {{Huber, Tobias and Peters, Wilhelm and Böcker, Joachim}},
  booktitle    = {{2014 International Power Electronics Conference (IPEC-Hiroshima 2014 - ECCE ASIA)}},
  publisher    = {{IEEE}},
  title        = {{{Monitoring critical temperatures in permanent magnet synchronous motors using low-order thermal models}}},
  doi          = {{10.1109/ipec.2014.6869785}},
  year         = {{2014}},
}

@inproceedings{30577,
  author       = {{Leuer, Michael and Böcker, Joachim}},
  booktitle    = {{2014 International Power Electronics Conference (IPEC-Hiroshima 2014 - ECCE ASIA)}},
  publisher    = {{IEEE}},
  title        = {{{Real-time implementation of an online Model Predictive Control for IPMSM using parallel computing on FPGA}}},
  doi          = {{10.1109/ipec.2014.6869605}},
  year         = {{2014}},
}

@inproceedings{30580,
  author       = {{Leuer, Michael and Ruting, Arne and Böcker, Joachim}},
  booktitle    = {{2014 IEEE International Energy Conference (ENERGYCON)}},
  publisher    = {{IEEE}},
  title        = {{{Efficiency-optimized Model Predictive Torque Control for IPMSM}}},
  doi          = {{10.1109/energycon.2014.6850398}},
  year         = {{2014}},
}

@inproceedings{30567,
  author       = {{Buchholz, Oleg and Böcker, Joachim}},
  booktitle    = {{IECON 2013 - 39th Annual Conference of the IEEE Industrial Electronics Society}},
  publisher    = {{IEEE}},
  title        = {{{FPGA-based dynamically reconfigurable control of induction motor drives}}},
  doi          = {{10.1109/iecon.2013.6699698}},
  year         = {{2014}},
}

@inproceedings{30578,
  author       = {{Vogt, T. and Peters, A. and Fröhleke, N. and Böcker, Joachim and Kempen, S.}},
  booktitle    = {{2014 International Power Electronics Conference (IPEC-Hiroshima 2014 - ECCE ASIA)}},
  publisher    = {{IEEE}},
  title        = {{{Power profile based selection and operation optimization of parallel-connected power converter combinations}}},
  doi          = {{10.1109/ipec.2014.6870091}},
  year         = {{2014}},
}

@inproceedings{30581,
  author       = {{Solanki, Jitendra and Fröhleke, Norbert and Böcker, Joachim and Duppe, Gregor and Averberg, Andreas and Wallmeier, Peter}},
  booktitle    = {{2014 IEEE Energy Conversion Congress and Exposition (ECCE)}},
  publisher    = {{IEEE}},
  title        = {{{Voltage sequence control based high-current rectifier system}}},
  doi          = {{10.1109/ecce.2014.6953958}},
  year         = {{2014}},
}

@inproceedings{30566,
  author       = {{Solanki, Jitendra and Fröhleke, Norbert and Böcker, Joachim}},
  booktitle    = {{IECON 2013 - 39th Annual Conference of the IEEE Industrial Electronics Society}},
  publisher    = {{IEEE}},
  title        = {{{A completely modular power converter for high-power high-current DC applications}}},
  doi          = {{10.1109/iecon.2013.6699127}},
  year         = {{2014}},
}

@inbook{17628,
  author       = {{Peckhaus, Volker}},
  booktitle    = {{Wissenschaftsphilosophie im Neukantianismus. Ansätze – Kontroversen – Wirkungen}},
  editor       = {{Krijnen, Christian and Zeidler, Kurt Walter}},
  pages        = {{233--253, Diskussion 254--257}},
  publisher    = {{Könighausen & Neumann}},
  title        = {{{Das Erkenntnisproblem und die Mathematik. Zum Streit zwischen dem Marburger Neukantianismus und dem Neofriesianismus}}},
  volume       = {{32}},
  year         = {{2014}},
}

@inbook{17629,
  abstract     = {{Rezension: Zeitschrift für philosophische Forschung 69 (2015), 614–615 (Thomas Uebel)}},
  author       = {{Peckhaus, Volker}},
  booktitle    = {{Fiktion und Fiktionalismus. Beiträge zu Hans Vaihingers Philosophie des Als Ob}},
  editor       = {{Neuber, Matthias}},
  pages        = {{91--106}},
  publisher    = {{Könighausen & Neumann}},
  title        = {{{Unsinn und Chance eines Fiktionalismus in der Logik}}},
  volume       = {{33}},
  year         = {{2014}},
}

@article{17633,
  abstract     = {{Rezension: Math. Rev. MR3330648 (L.G. González); Zbl. Math. 1315.01023 (T.-L. Rădulescu)}},
  author       = {{Peckhaus, Volker}},
  journal      = {{Revue d’histoire des sciences}},
  pages        = {{207--230}},
  title        = {{{Ernst Schröder on Pasigraphy (Dossier de la logique philosophique à la logique mathématique)}}},
  volume       = {{67}},
  year         = {{2014}},
}

@book{17889,
  editor       = {{Peckhaus, Volker}},
  title        = {{{In memoriam Helmar Frank}}},
  volume       = {{133}},
  year         = {{2014}},
}

@inproceedings{22030,
  abstract     = {{Parts produced by Fused Deposition Modeling (FDM) tend to have rough and undulating surfaces with staircase effects on rounded and slanting areas of the part. This is due to the characteristics of the process. In many fields of application, high demands are made on the optical quality of the part. An improvement in the surface quality of FDM parts made of Ultem*9085 can be achieved through post-treatment with a mass finishing process. In this paper, FDM specimens are post-treated in a disk finishing unit. Influences of the mass finishing process are analyzed with regard to the dependence of surface quality on the various process parameters and on the finishing medium, grinding time and grinding speed. The finishing efficiency depends on the finishing media and decreases for lower finishing time. For all media a lower disk velocity results a smaller grinding effect, but there are clearly differences between the finishing media. The paper also discusses effects of the grinding process on the mechanical properties of the parts. Especially small part geometries and parts build in z-direction tend to break during the finishing process.}},
  author       = {{Fischer, M. and Schöppner, Volker}},
  booktitle    = {{ANTEC}},
  isbn         = {{978-1-63439-708-7}},
  pages        = {{2331--2336}},
  publisher    = {{SPE: Society of Plastics Engineers}},
  title        = {{{Effects of a mass finishing process on parts produced from Ultem 9085 by Fused Deposition Modeling}}},
  year         = {{2014}},
}

@inproceedings{22021,
  abstract     = {{Additive production techniques have the advantage of manufacturing parts without needing a forming tool. One of the most used additive manufacturing processes is "Fused Deposition Modeling" (FDM) which allows the production of prototypes and end-use parts. Due to the manufacture layer by layer, also complex part geometries can be created in one working step. Furthermore, lightweight parts with specific inner core structures can be manufactured in order to achieve good weightrelated strength properties. In this paper the mechanical behavior of lightweight parts manufactured with the 3D production system Fortus 400mc from Stratasys and the material Polyetherimide (PEI) with the trade name Ultem*9085 is analyzed. The test specimens were built up with different inner structures and building directions. Therefore, test specimens with known lightweight core geometries (e.g. corrugated and honeycomb cores) were designed. A four-point bending test was conducted to analyze the strength properties as well as the weight-related strength properties. Additionally the influence of the structure width, the structure wall thickness and the top layer thickness was analyzed using a honeycomb structure.}},
  author       = {{Bagsik, A. and Josupeit, S. and Schöppner, Volker and Klemp, E.}},
  booktitle    = {{29th International Conference of the Polymer Processing Society}},
  pages        = {{696--701}},
  publisher    = {{American Institute of Physics }},
  title        = {{{Mechanical Analysis of Lightweight Constructions manufactured with Fused Deposition Modeling}}},
  doi          = {{10.1063/1.4873874}},
  volume       = {{29}},
  year         = {{2014}},
}

@phdthesis{30588,
  author       = {{Specht, A.}},
  title        = {{{Ermittlung der Rotortemperatur einer Synchronmaschine mit eingebetteten Permanentmagneten für einen automobilen Traktionsantrieb mittels Beobachter basierend auf elektrischen Größen}}},
  year         = {{2014}},
}

@phdthesis{30574,
  author       = {{Cao, Z.}},
  isbn         = {{978-3-8440-2785-3}},
  title        = {{{Model-Based Development of DC-DC Converters with Wide Operation Range and High Dynamics}}},
  year         = {{2014}},
}

@phdthesis{30572,
  author       = {{Hu, M.}},
  title        = {{{Modeling Optimization and Control Design for LCC Resonant Converter Applied in Very Low Frequency High Voltage Generator}}},
  year         = {{2014}},
}

@phdthesis{30548,
  author       = {{Pohlenz, Daniel}},
  title        = {{{Wirkungsgradoptimale Regelung eines elektrischen Fahrantriebes mit variabler Zwischenkreisspannung}}},
  year         = {{2014}},
}